參數資料
型號: DS89C450-QNL
英文描述: Ultra-High-Speed Flash Microcontrollers
中文描述: 超高速閃存微控制器
文件頁數: 3/48頁
文件大?。?/td> 656K
代理商: DS89C450-QNL
DS89C430/DS89C440/DS89C450 Ultra-High-Speed Flash Microcontrollers
3 of 48
Note 1:
Note 2:
Note 3:
Specifications to -40°C are guaranteed by design and not production tested.
All voltages are referenced to ground.
The user should note that this part is tested and guaranteed to operate down to 4.5V (10%) and that V
RST
(min) is specified below
that point. This indicates that there is a range of voltages [(V
MIN
to V
RST
(min)] where the processor's operation is not guaranteed, but
the reset trip point has not been reached. This should not be an issue in most applications, but should be considered when proper
operation must be maintained at all times. For these applications, it may be desirable to use a more accurate external reset.
Note 4:
While the specifications for V
PFW
and V
RST
overlap, the design of the hardware makes it so this is not possible. Within the ranges
given, there is guaranteed separation between these two voltages.
Note 5:
Active current is measured with a 33MHz clock source driving XTAL1, V
CC
= RST = 5.5V. All other pins are disconnected.
Note 6:
Idle mode current is measured with a 33MHz clock source driving XTAL1, V
CC
= 5.5V, RST at ground. All other pins are
disconnected.
Stop mode is measured with XTAL and RST grounded, V
CC
= 5.5V. All other pins are disconnected.
Note 7:
Note 8:
Note 9:
RST = 5.5V. This condition mimics the operation of pins in I/O mode.
During a 0-to-1 transition, a one shot drives the ports hard for two clock cycles. This measurement reflects a port pin in transition
mode.
Note 10:
When addressing external memory.
Note 11:
Guaranteed by design.
Note 12:
Ports 1, 2, and 3 source transition current when pulled down externally. The current reaches its maximum at approximately 2V.
Note 13:
RST = 5.5V. Port 0 is floating during reset and when in the logic-high state during I/O mode.
Note 14:
This port is a weak address holding latch in bus mode. Peak current occurs near the input transition point of the holding latch at
approximately 2V.
相關PDF資料
PDF描述
DS89C430-DS89C450 Ultra-High-Speed Flash Microcontrollers
DS89C450 RES,Wirewound,301Ohms,1+/-% Tol,-20,20ppm-TC,4427-Case
DS907X SipStik Connectors
DS9090K 1-Wire Memory Evaluation Kit
DS9093A iButton Key Ring Mounts
相關代理商/技術參數
參數描述
DS89C450-QNL+ 功能描述:8位微控制器 -MCU Ultra-High-Speed Flash MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS89LV21TM 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transceiver
DS89LV21TN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Transceiver
DS8T26A 制造商:NSC 制造商全稱:National Semiconductor 功能描述:4-Bit Bidirectional Bus Transceivers
DS8T26AJ 制造商:未知廠家 制造商全稱:未知廠家 功能描述:4-Bit Bus Transceiver