- 您現在的位置：買賣IC網 > PDF目錄377001 > DSP56F826 (飛思卡爾半導體(中國)有限公司) 16-bit Hybrid Controller(16位混合控制器) PDF資料下載
參數資料
| 型號： | DSP56F826 |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 16-bit Hybrid Controller(16位混合控制器) |
| 中文描述： | 16位混合控制器（16位混合控制器） |
| 文件頁數： | 46/48頁 |
| 文件大?。?/td> | 1011K |
| 代理商： | DSP56F826 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁
46
56F826 Technical Data
Use the value obtained by the equation (T
J
– T
T
)/P
D
, where T
T
is the temperature of the package
case determined by a thermocouple.
The thermal characterization parameter is measured per JESD51-2 specification using a 40-gauge type T
thermocouple epoxied to the top center of the package case. The thermocouple should be positioned so that
the thermocouple junction rests on the package. A small amount of epoxy is placed over the thermocouple
junction and over about 1mm of wire extending from the junction. The thermocouple wire is placed flat
against the package case to avoid measurement errors caused by cooling effects of the thermocouple wire.
When heat sink is used, the junction temperature is determined from a thermocouple inserted at the interface
between the case of the package and the interface material. A clearance slot or hole is normally required in
the heat sink. Minimizing the size of the clearance is important to minimize the change in thermal
performance caused by removing part of the thermal interface to the heat sink. Because of the experimental
difficulties with this technique, many engineers measure the heat sink temperature and then back-calculate
the case temperature using a separate measurement of the thermal resistance of the interface. From this case
temperature, the junction temperature is determined from the junction-to-case thermal resistance.
5.2 Electrical Design Considerations
Use the following list of considerations to assure correct operation:
Provide a low-impedance path from the board power supply to each V
DD,
V
DDIO,
and V
DDA
pin on
the hybrid controller, and from the board ground to each V
SS,
V
SSIO,
and V
SSA
(GND) pin.
The minimum bypass requirement is to place 0.1
μ
F capacitors positioned as close as possible to the
package supply pins. The recommended bypass configuration is to place one bypass capacitor on
each of the V
DD
/V
SS
pairs, including V
DDA
/V
SSA
and V
DDIO
/V
SSIO.
Ceramic and tantalum
capacitors tend to provide better performance tolerances.
Ensure that capacitor leads and associated printed circuit traces that connect to the chip V
DD,
V
DDIO,
and V
DDA
and V
SS,
V
SSIO,
and V
SSA
(GND) pins are less than 0.5 inch per capacitor lead.
Bypass the V
DD
and V
SS
layers of the PCB with approximately 100
μ
F, preferably with a high-grade
capacitor such as a tantalum capacitor.
Because the controller’s output signals have fast rise and fall times, PCB trace lengths should be
minimal.
CAUTION
This device contains protective circuitry to guard
against damage due to high static voltage or
electrical fields. However, normal precautions are
advised to avoid application of any voltages higher
than maximum-rated voltages to this high-impedance
circuit. Reliability of operation is enhanced if unused
inputs are tied to an appropriate voltage level.
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| DSP56F827E | 16-bit Digital Signal Controllers |
| DSP56F827FG80 | 16-bit Digital Signal Controllers |
| DSP56F827FG80E | 16-bit Digital Signal Controllers |
| DSP56F827 | 16-bit Hybrid Controller(16位混合控制器) |
| DSP8-08AC | Phase-leg Rectifier Diode ISOPLUS220 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSP56F826-827UM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:16-Bit Digital Signal Processor Users Manual |
| DSP56F826-827UM/D | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:56F827 16-bit Hybrid Controller |
| DSP56F826BU80 | 功能描述:數字信號處理器和控制器 - DSP, DSC 80Mhz/ 40MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSP56F826BU80E | 功能描述:數字信號處理器和控制器 - DSP, DSC 80Mhz/40MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSP56F826BU80E | 制造商:Freescale Semiconductor 功能描述:Digital Signal Processor IC DSP Type:Cor |
發布緊急采購，3分鐘左右您將得到回復。