- 您現在的位置：買賣IC網 > PDF目錄377002 > DSPCOMMANDUM Universal Command Converter for DSP User＇s Manual PDF資料下載
參數資料
| 型號： | DSPCOMMANDUM |
| 英文描述： | Universal Command Converter for DSP User＇s Manual |
| 中文描述： | 通用命令轉換為數字信號處理器用戶手冊 |
| 文件頁數： | 18/70頁 |
| 文件大?。?/td> | 550K |
| 代理商： | DSPCOMMANDUM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
2-2
Universal Command Converter
Motorola
Host Computer Interface Card
ISA expansion slots. A single PC-workstation interface card can control up to eight
command converters.
2.1.1.1 Installing the PC-Workstation’s Interface
Refer to the appropriate installation and set-up manual for your PC-workstation for
instructions on removing the system cover.
Jumper group JG1 selects the interrupt asserted on the host processor by the host interface
card when the target DSP device makes a service request (for example, by reaching a
breakpoint).
Note:
The ADS software does not support interrupts. No jumper should be placed on
JG1 when used with the ADS software.
Jumper group JG2 specifies the host interface card I/O address. The host interface card
supports 16-bit I/O addresses and uses three consecutive addresses from the specified
address. The starting address may be configured, with jumper pairs A8–A15 in JG2, to
any multiple of $100, up to $FF00. Place a jumper over a pair of pins to set that address bit
to 0; remove the jumper to set the address bit to 1. Address bits A0–A7 are not decoded. In
Figure 2-2, the selected address range is $100–$102.
Note:
Although the host interface card supports 16-bit addressing, the ADS software
only supports addresses $100, $200, and $300.
Once you have ensured that the selected address does not conflict with another expansion
card installed in the motherboard, you may install the host interface card. Figure 2-2
illustrates the physical locations of JG1 and JG2.
Warning
Before removing or
installing any equipment
in the PC-workstation
computer, turn off the
power and disconnect the
power cord.
相關PDF資料 |
PDF描述 |
|---|---|
| DSPCOMMPARALLELUM | Parallel Port Command Converter for DSP User＇s Manual |
| DSPCOMMPCIUM | PCI Command Converter for DSP User＇s Manual |
| DSPG4001-71 | Telecommunication IC |
| DSPG5002 | Analog IC |
| DSPG5003 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPCOMMPARALLEL | 功能描述:程序設計器配件 PARALLEL COMMAND CONV RoHS:否 制造商:Lattice 產品:ispDOWNLOAD Cables 用于:In-system Programming |
| DSPCOMMPARALLELE | 功能描述:界面開發工具 PARALLEL COMMAND CONV RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V |
| DSPCOMMPARALLELE | 制造商:Freescale Semiconductor 功能描述:PARALLEL COMMAND CONV |
| DSPCOMMPARALLELUM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Parallel Port Command Converter for DSP User＇s Manual |
| DSPCOMMPCIUM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI Command Converter for DSP User＇s Manual |
發布緊急采購，3分鐘左右您將得到回復。
