- 您現在的位置：買賣IC網 > PDF目錄377002 > DSPCOMMPARALLELUM Parallel Port Command Converter for DSP User＇s Manual PDF資料下載
參數資料
| 型號： | DSPCOMMPARALLELUM |
| 英文描述： | Parallel Port Command Converter for DSP User＇s Manual |
| 中文描述： | 并行端口命令轉換為數字信號處理器用戶手冊 |
| 文件頁數： | 18/70頁 |
| 文件大?。?/td> | 550K |
| 代理商： | DSPCOMMPARALLELUM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
2-2
Universal Command Converter
Motorola
Host Computer Interface Card
ISA expansion slots. A single PC-workstation interface card can control up to eight
command converters.
2.1.1.1 Installing the PC-Workstation’s Interface
Refer to the appropriate installation and set-up manual for your PC-workstation for
instructions on removing the system cover.
Jumper group JG1 selects the interrupt asserted on the host processor by the host interface
card when the target DSP device makes a service request (for example, by reaching a
breakpoint).
Note:
The ADS software does not support interrupts. No jumper should be placed on
JG1 when used with the ADS software.
Jumper group JG2 specifies the host interface card I/O address. The host interface card
supports 16-bit I/O addresses and uses three consecutive addresses from the specified
address. The starting address may be configured, with jumper pairs A8–A15 in JG2, to
any multiple of $100, up to $FF00. Place a jumper over a pair of pins to set that address bit
to 0; remove the jumper to set the address bit to 1. Address bits A0–A7 are not decoded. In
Figure 2-2, the selected address range is $100–$102.
Note:
Although the host interface card supports 16-bit addressing, the ADS software
only supports addresses $100, $200, and $300.
Once you have ensured that the selected address does not conflict with another expansion
card installed in the motherboard, you may install the host interface card. Figure 2-2
illustrates the physical locations of JG1 and JG2.
Warning
Before removing or
installing any equipment
in the PC-workstation
computer, turn off the
power and disconnect the
power cord.
相關PDF資料 |
PDF描述 |
|---|---|
| DSPCOMMPCIUM | PCI Command Converter for DSP User＇s Manual |
| DSPG4001-71 | Telecommunication IC |
| DSPG5002 | Analog IC |
| DSPG5003 | Analog IC |
| DSPG5003-11 | Cell-Phone Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPCOMMPCIUM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI Command Converter for DSP User＇s Manual |
| DSPD374DB1 | 制造商:Freescale Semiconductor 功能描述:"D" ROM DAUGHTER CARD - Boxed Product (Development Kits) |
| DSPD56367AG150 | 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPD56371AF180 | 制造商:Freescale Semiconductor 功能描述: 制造商:Freescale Semiconductor 功能描述:DSP FIXED-POINT 24-BIT 181MHZ 181MIPS 80-PIN LQFP TRAY - Trays 制造商:Freescale Semiconductor 功能描述:AUDIO DSP |
| DSPD56374AE | 制造商:Freescale Semiconductor 功能描述:DSP FIXED-POINT 24-BIT 150MHZ 150MIPS 52-PIN LQFP TRAY - Trays 制造商:Freescale Semiconductor 功能描述:56374 52LQFP ROM D 0-70 |
發布緊急采購，3分鐘左右您將得到回復。