- 您現在的位置：買賣IC網 > PDF目錄377002 > DSPCOMMPARALLELUM Parallel Port Command Converter for DSP User＇s Manual PDF資料下載
參數資料
| 型號： | DSPCOMMPARALLELUM |
| 英文描述： | Parallel Port Command Converter for DSP User＇s Manual |
| 中文描述： | 并行端口命令轉換為數字信號處理器用戶手冊 |
| 文件頁數： | 33/70頁 |
| 文件大?。?/td> | 550K |
| 代理商： | DSPCOMMPARALLELUM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
Motorola
Functional Description
3-1
Chapter 3
Functional Description
The application development system (ADS) user interacts with the target DSP through
two subsystem components, the host computer interface and the command converter
controller. The host computer interface consists of a program written in the C language
that interacts with a host computer bus interface card. The command converter consists of
a program written in DSP56002 assembly language which interacts with the host
computer bus interface card and the target JTAG/OnCE port.
It should be noted that older versions of Motorola DSP products use the OnCE port
protocol, while newer versions of Motorola DSP products use the IEEE JTAG 4-wire
protocol to interact with their OnCE port. New versions of the command converter support
both JTAG and OnCE protocols.
Commands entered from the host computer’s keyboard are parsed and a series of low level
command packets are sent to the command converter. The command converter translates
these low level command packets into serial sequences that are transferred to the target
DSP via its JTAG/OnCE port. The JTAG/OnCE port provides the necessary control to the
target so programs may be loaded or saved, registers read or modified, and hardware
breakpoints set or cleared.
The host computer interface is designed to communicate with as many as eight command
converter cards. This requires a special software protocol to avoid data collisions between
one target and another. The purpose of this section is to describe the subsystem
components of the ADS to give a better understanding of the communication link between
the user and the target DSP.
3.1 Host Computer Hardware
The host computer’s hardware interface provides the communications link between the
user and the command converter. The ADS user interface program uses a software
handshake when communicating with the command converter. There are signals defined
on the host computer bus interface card which are used for requesting and acknowledging
information transfer. Since the handshake is software driven the transfer rate will be
相關PDF資料 |
PDF描述 |
|---|---|
| DSPCOMMPCIUM | PCI Command Converter for DSP User＇s Manual |
| DSPG4001-71 | Telecommunication IC |
| DSPG5002 | Analog IC |
| DSPG5003 | Analog IC |
| DSPG5003-11 | Cell-Phone Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPCOMMPCIUM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI Command Converter for DSP User＇s Manual |
| DSPD374DB1 | 制造商:Freescale Semiconductor 功能描述:"D" ROM DAUGHTER CARD - Boxed Product (Development Kits) |
| DSPD56367AG150 | 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPD56371AF180 | 制造商:Freescale Semiconductor 功能描述: 制造商:Freescale Semiconductor 功能描述:DSP FIXED-POINT 24-BIT 181MHZ 181MIPS 80-PIN LQFP TRAY - Trays 制造商:Freescale Semiconductor 功能描述:AUDIO DSP |
| DSPD56374AE | 制造商:Freescale Semiconductor 功能描述:DSP FIXED-POINT 24-BIT 150MHZ 150MIPS 52-PIN LQFP TRAY - Trays 制造商:Freescale Semiconductor 功能描述:56374 52LQFP ROM D 0-70 |
發布緊急采購，3分鐘左右您將得到回復。