參數資料
型號： DSPCOMMPCIUM
英文描述： PCI Command Converter for DSP User＇s Manual
中文描述： 的PCI命令轉換為數字信號處理器用戶手冊
文件頁數： 25/70頁
文件大?。?/td> 550K
代理商： DSPCOMMPCIUM
Host Computer Interface Card
Motorola
Preparation and Installation
2-9
tar xvf /dev/rmt/0m
The number at the end of the command is the device number and should be changed if the
CD drive number is different on the machine being used. After the files are extracted from
the CD-ROM, a directory named “driver” is created.
The user must be logged in as “root” or superuser to proceed from this point. The
following steps should be followed for proper installation of the driver program:
Note:
“hostname#” represents the system prompt; that is, it is not to be entered as part
of the command.
The HP device driver for the ADS supports multiple host interface cards (up to three,
limited by the addresses that can be selected on the host interface card) installed into a
single HP-700 workstation.
1. When the files were installed, a directory called driver was created in the hierarchy.
Make this the current directory now by executing the following command, where
ADS-PATH is the path to where the ADS files were installed:
hostname# cd /ADS-PATH/driver
2. Copy and change the ownership, group and mode of the device driver library file,
libmdsp.a, using the following commands:
hostname# cp libmdsp.a /etc/conf
hostname# chown bin /etc/conf/libmdsp.a
hostname# chgrp bin /etc/conf/libmdsp.a
hostname# chmod 444 /etc/conf/libmdsp.a
3. To install the device configuration file, type the following command. (Note that it
may be necessary to escape the ! by using a backslash \, depending on the shell you
are using.)
hostname# cp !MOT0010.CFG /etc/eisa
This copies the configuration file into the system EISA configuration directory.
Modify the copy of the file in /etc/eisa to reflect the I/O port that the card is
configured for (change the PORT entry).
If you are using multiple host interface cards in your HP, make multiple copies of
this file in /etc/eisa, changing the last digit of the file name on each copy. Modify
each copy to have the correct ID and PORT entries (the ID entry should be the
name of the file without the .CFG extension). Each PORT entry should be modified
to contain the proper addresses for the additional cards that are supported.
4. Run the EISA configuration program by typing this command:
hostname# /etc/eisa_config
相關PDF資料
PDF描述
DSPG4001-71 Telecommunication IC
DSPG5002 Analog IC
DSPG5003 Analog IC
DSPG5003-11 Cell-Phone Circuit
DSPG5004 Analog IC
相關代理商/技術參數
參數描述
DSPD374DB1 制造商:Freescale Semiconductor 功能描述:"D" ROM DAUGHTER CARD - Boxed Product (Development Kits)
DSPD56367AG150 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
DSPD56371AF180 制造商:Freescale Semiconductor 功能描述: 制造商:Freescale Semiconductor 功能描述:DSP FIXED-POINT 24-BIT 181MHZ 181MIPS 80-PIN LQFP TRAY - Trays 制造商:Freescale Semiconductor 功能描述:AUDIO DSP
DSPD56374AE 制造商:Freescale Semiconductor 功能描述:DSP FIXED-POINT 24-BIT 150MHZ 150MIPS 52-PIN LQFP TRAY - Trays 制造商:Freescale Semiconductor 功能描述:56374 52LQFP ROM D 0-70
DSPD56374AEC 制造商:Freescale Semiconductor 功能描述:DSP FIXED-POINT 24-BIT 150MHZ 150MIPS 52-PIN LQFP TRAY - Trays
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*