- 您現在的位置：買賣IC網 > PDF目錄3856 > DSPIC30F2012-30I/ML (Microchip Technology)IC DSPIC MCU/DSP 12K 28QFN PDF資料下載
參數資料
| 型號： | DSPIC30F2012-30I/ML |
| 廠商： | Microchip Technology |
| 文件頁數： | 31/66頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSPIC MCU/DSP 12K 28QFN |
| 產品培訓模塊： | Serial Communications using dsPIC30F I2C Serial Communications using dsPIC30F SPI Serial Communications using dsPIC30F UART dsPIC30F 12 bit ADC - Part 2 dsPIC30F Addressing Modes - Part 1 dsPIC30F Architecture - Part 1 dsPIC30F DSP Engine & ALU dsPIC30F Interrupts dsPIC30F Motor Control PWM dsPIC Timers Asynchronous Stimulus dsPIC30F Addressing Modes - Part 2 dsPIC30F Architecture - Part 2 dsPIC30F 12-bit ADC Part 1 |
| 標準包裝： | 61 |
| 系列： | dsPIC™ 30F |
| 核心處理器： | dsPIC |
| 芯體尺寸： | 16-位 |
| 速度： | 30 MIP |
| 連通性： | I²C，SPI，UART/USART |
| 外圍設備： | 欠壓檢測/復位，POR，PWM，WDT |
| 輸入/輸出數： | 20 |
| 程序存儲器容量： | 12KB（4K x 24） |
| 程序存儲器類型： | 閃存 |
| RAM 容量： | 1K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.5 V ~ 5.5 V |
| 數據轉換器： | A/D 10x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 28-VQFN 裸露焊盤 |
| 包裝： | 管件 |
| 產品目錄頁面： | 650 (CN2011-ZH PDF) |
| 配用： | AC164322-ND - MODULE SOCKET MPLAB PM3 28/44QFN DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE |
| 其它名稱： | DSPIC30F201230IML |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
2010 Microchip Technology Inc.
DS70102K-page 37
dsPIC30F Flash Programming Specification
11.4
Flash Memory Programming in
ICSP Mode
Programming in ICSP mode is described in
ming Cycle”. Step-by-step procedures are described
Normal-Voltage Systems” through Section 11.13
“Reading the Application ID Word”. All programming
operations must use serial execution, as described in
11.4.1
PROGRAMMING OPERATIONS
Flash memory write and erase operations are
controlled by the NVMCON register. Programming is
performed by setting NVMCON to select the type of
erase operation (Table 11-2) or write operation
(Table 11-3), writing a key sequence to enable the
programming and initiating the programming by setting
the WR control bit, NVMCON<15>.
In ICSP mode, all programming operations are
externally timed. An external 2 ms delay must be used
between setting the WR control bit and clearing the WR
control bit to complete the programming operation.
TABLE 11-2:
NVMCON ERASE
OPERATIONS
NVMCON
Value
Erase Operation
0x407F
Erase all code memory, data memory
(does not erase UNIT ID).
0x4075
Erase 1 row (16 words) of data
EEPROM.
0x4074
Erase 1 word of data EEPROM.
0x4072
Erase all executive memory.
0x4071
Erase 1 row (32 instruction words)
from 1 panel of code memory.
0x406E
Erase Boot Secure and General
Segments, then erase FBS, FSS and
FGS configuration registers.
0x4066
Erase all Data EEPROM allocated to
Boot Segment.
0x405E
Erase Secure and General Segments,
then erase FSS and FGS configuration
registers.
0x4056
Erase all Data EEPROM allocated to
Secure Segment.
0x404E
Erase General Segment, then erase
FGS configuration register.
0x4046
Erase all Data EEPROM allocated to
General Segment.
TABLE 11-3:
NVMCON WRITE
OPERATIONS
NVMCON
Value
Write Operation
0x4008
Write 1 word to configuration
memory.
0x4005
Write 1 row (16 words) to data memory.
0x4004
Write 1 word to data memory.
0x4001
Write 1 row (32 instruction words) into
1 panel of program memory.
11.4.2
UNLOCKING NVMCON FOR
PROGRAMMING
Writes to the WR bit (NVMCON<15>) are locked to
prevent accidental programming from taking place.
Writing a key sequence to the NVMKEY register
unlocks the WR bit and allows it to be written to. The
unlock sequence is performed as follows:
MOV
#0x55, W8
MOV
W8, NVMKEY
MOV
#0xAA, W9
MOV
W9, NVMKEY
Note:
Any working register, or working register
pair, can be used to write the unlock
sequence.
11.4.3
STARTING AND STOPPING A
PROGRAMMING CYCLE
Once the unlock key sequence has been written to the
NVMKEY register, the WR bit (NVMCON<15>) is used
to start and stop an erase or write cycle. Setting the WR
bit initiates the programming cycle. Clearing the WR bit
terminates the programming cycle.
All erase and write cycles must be externally timed. An
external delay must be used between setting and
clearing the WR bit. Starting and stopping a
programming cycle is performed as follows:
BSET
NVMCON, #WR
<Wait 2 ms>
BCLR
NVMCON, #WR
11.5
Erasing Program Memory in
Normal-Voltage Systems
The procedure for erasing program memory (all code
memory, data memory, executive memory and code-
protect bits) consists of setting NVMCON to 0x407F,
unlocking NVMCON for erasing and then executing the
programming cycle. This method of bulk erasing pro-
gram memory only works for systems where VDD is
between 4.5 volts and 5.5 volts. The method for erasing
program memory for systems with a lower VDD (3.0
volts-4.5 volts) is described in Section 6.1 “Erasing
相關PDF資料 |
PDF描述 |
|---|---|
| ATMEGA16-16PI | IC AVR MCU 16K 16MHZ IND 40-DIP |
| ATMEGA128-16MI | IC AVR MCU 128K 16MHZ IND 64-QFN |
| T89C51CC02UA-SITIM | IC 8051 MCU FLASH 16K 28PLCC |
| T89C51CC01UA-SLSIM | IC 8051 MCU FLASH 32K 44PLCC |
| T89C51CC01UA-RLTIM | IC 8051 MCU FLASH 32K 44VQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPIC30F2012A20E/ML | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers |
| DSPIC30F2012A-20E/ML | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers |
| DSPIC30F2012A20E/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers |
| DSPIC30F2012A-20E/P | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers |
| DSPIC30F2012A20E/SO | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers |
發布緊急采購，3分鐘左右您將得到回復。