參數資料
型號： DSPIC30F2012-30I/ML
廠商： Microchip Technology
文件頁數： 49/66頁
文件大?。?/td> 0K
描述： IC DSPIC MCU/DSP 12K 28QFN
產品培訓模塊： Serial Communications using dsPIC30F I2C
Serial Communications using dsPIC30F SPI
Serial Communications using dsPIC30F UART
dsPIC30F 12 bit ADC - Part 2
dsPIC30F Addressing Modes - Part 1
dsPIC30F Architecture - Part 1
dsPIC30F DSP Engine & ALU
dsPIC30F Interrupts
dsPIC30F Motor Control PWM
dsPIC Timers
Asynchronous Stimulus
dsPIC30F Addressing Modes - Part 2
dsPIC30F Architecture - Part 2
dsPIC30F 12-bit ADC Part 1
標準包裝： 61
系列： dsPIC™ 30F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 30 MIP
連通性： I²C，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 20
程序存儲器容量： 12KB（4K x 24）
程序存儲器類型： 閃存
RAM 容量： 1K x 8
電壓 - 電源 (Vcc/Vdd)： 2.5 V ~ 5.5 V
數據轉換器： A/D 10x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 28-VQFN 裸露焊盤
包裝： 管件
產品目錄頁面： 650 (CN2011-ZH PDF)
配用： AC164322-ND - MODULE SOCKET MPLAB PM3 28/44QFN
DV164005-ND - KIT ICD2 SIMPLE SUIT W/USB CABLE
其它名稱： DSPIC30F201230IML
2010 Microchip Technology Inc.
DS70102K-page 53
dsPIC30F Flash Programming Specification
11.13 Reading the Application ID Word
The application ID word is stored at address 0x8005BE
in executive code memory. To read this memory
location, you must use the SIX control code to move
this program memory location to the VISI register. The
REGOUT control code must then be used to clock the
contents of the VISI register out of the device. The
corresponding control and instruction codes that must
be serially transmitted to the device to perform this
operation are shown in Table 11-13.
Once the programmer has clocked-out the application
ID word, it must be inspected. If the application ID has
the value 0xBB, the programming executive is resident
in memory and the device can be programmed using
the mechanism described in Section 5.0 “Device
Programming”. However, if the application ID has any
other value, the programming executive is not resident
in memory. It must be loaded to memory before the
device can be programmed. The procedure for loading
the programming executive to the memory is described
11.14 Exiting ICSP Mode
After confirming that the programming executive is
resident in memory, or loading the programming
executive, ICSP mode is exited by removing power to
the device or bringing MCLR to VIL. Programming can
then take place by following the procedure outlined in
TABLE 11-13: SERIAL INSTRUCTION EXECUTION FOR READING THE APPLICATION ID WORD
Command
(Binary)
Data
(Hexadecimal)
Description
Step 1: Exit the Reset vector.
0000
040100
000000
GOTO 0x100
NOP
Step 2: Initialize TBLPAG and the read pointer (W0) for TBLRD instruction.
0000
200800
880190
205BE0
207841
000000
BA0890
000000
MOV
#0x80, W0
MOV
W0, TBLPAG
MOV
#0x5BE, W0
MOV
VISI, W1
NOP
TBLRDL [W0], [W1]
NOP
Step 3: Output the VISI register using the REGOUT command.
0001
0000
<VISI>
000000
Clock out contents of the VISI register
NOP
相關PDF資料
PDF描述
ATMEGA16-16PI IC AVR MCU 16K 16MHZ IND 40-DIP
ATMEGA128-16MI IC AVR MCU 128K 16MHZ IND 64-QFN
T89C51CC02UA-SITIM IC 8051 MCU FLASH 16K 28PLCC
T89C51CC01UA-SLSIM IC 8051 MCU FLASH 32K 44PLCC
T89C51CC01UA-RLTIM IC 8051 MCU FLASH 32K 44VQFP
相關代理商/技術參數
參數描述
DSPIC30F2012A20E/ML 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers
DSPIC30F2012A-20E/ML 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers
DSPIC30F2012A20E/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers
DSPIC30F2012A-20E/P 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers
DSPIC30F2012A20E/SO 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-Bit Digital Signal Controllers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*