參數資料
型號： DSPIC33FJ16GP304T-I/PT
廠商： Microchip Technology
文件頁數： 129/176頁
文件大小： 0K
描述： IC DSPIC MCU/DSP 16K 44TQFP
產品培訓模塊： Asynchronous Stimulus
標準包裝： 1,200
系列： dsPIC™ 33F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 40 MIP
連通性： I²C，IrDA，LIN，SPI，UART/USART
外圍設備： 欠壓檢測/復位，POR，PWM，WDT
輸入/輸出數： 35
程序存儲器容量： 16KB（16K x 8）
程序存儲器類型： 閃存
RAM 容量： 2K x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 3.6 V
數據轉換器： A/D 13x12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 44-TQFP
包裝： 帶卷 (TR)
配用： DV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
DM240001-ND - BOARD DEMO PIC24/DSPIC33/PIC32
其它名稱： DSPIC33FJ16GP304T-I/PTTR
dsPIC33FJ32GP202/204 and dsPIC33FJ16GP304
DS70290J-page 56
2007-2011 Microchip Technology Inc.
5.2
RTSP Operation
The
dsPIC33FJ32GP202/204
and
dsPIC33FJ16GP304 Flash program memory array is
organized into rows of 64 instructions or 192 bytes.
RTSP allows the user application to erase a page of
memory, which consists of eight rows (512 instructions)
at a time, and to program one row or one word at a
time. The 8-row erase pages and single row write rows
are edge-aligned from the beginning of program
memory, on boundaries of 1536 bytes and 192 bytes,
respectively.
The program memory implements holding buffers that
can contain 64 instructions of programming data. Prior
to the actual programming operation, the write data
must be loaded into the buffers sequentially. The
instruction words loaded must always be from a group
of 64 boundary.
The basic sequence for RTSP programming is to set up
a Table Pointer, then do a series of TBLWT instructions
to load the buffers. Programming is performed by
setting the control bits in the NVMCON register. A total
of 64 TBLWTL and TBLWTH instructions are required
to load the instructions.
All of the table write operations are single-word writes
(two instruction cycles) because only the buffers are
written. A programming cycle is required for
programming each row.
5.3
Programming Operations
A complete programming sequence is necessary for
programming or erasing the internal Flash in RTSP
mode.
The
processor stalls (waits)
until
the
programming operation is finished.
The programming time depends on the FRC accuracy
(see Table 22-18) and the value of the FRC Oscillator
Tuning register (see Register 8-4). Use the following
formula to calculate the minimum and maximum values
for the Row Write Time, Page Erase Time, and Word
Write Cycle Time parameters (see Table 22-12).
EQUATION 5-1:
PROGRAMMING TIME
For example, if the device is operating at +125
° C, the
FRC accuracy will be ±5%. If the TUN<5:0> bits (see
Register 8-4) are set to ‘b111111, the minimum row
write time is equal to Equation 5-2.
EQUATION 5-2:
MINIMUM ROW WRITE
TIME
The maximum row write time is equal to Equation 5-3.
EQUATION 5-3:
MAXIMUM ROW WRITE
TIME
Setting the WR bit (NVMCON<15>) starts the
operation, and the WR bit is automatically cleared
when the operation is finished.
5.4
Flash Memory Resources
Many useful resources are provided on the main prod-
uct page of the Microchip web site for the devices listed
in this data sheet. This product page, which can be
accessed using this link, contains the latest updates
and additional information.
5.4.1
KEY RESOURCES
Section 5. “Flash Programming” (DS70191)
Code Samples
Application Notes
Software Libraries
Webinars
All related dsPIC33F/PIC24H Family Reference
Manuals Sections
Development Tools
5.5
Control Registers
The two SFRs that are used to read and write the
program Flash memory are:
The NVMCON register (Register 5-1) controls which
blocks are to be erased, which memory type is to be
programmed and the start of the programming cycle.
NVMKEY (Register 5-2) is a write-only register that is
used for write protection. To start a programming or
erase
sequence,
the
user
application
must
consecutively write 0x55 and 0xAA to the NVMKEY
register.
Refer
to
Operations” for further details.
T
7.37 MHz
FRC Accuracy
()%
FRC Tuning
()%
×
----------------------------------------------------------------------------------------------------------------------------
TRW
11064 Cycles
7.37 MHz
10.05
+
()
1 0.00375
–
()
×
------------------------------------------------------------------------------------------------ 1.435ms
=
Note:
In the event you are not able to access
the product page using the link above,
enter
this
URL
in
your
browser:
TRW
11064 Cycles
7.37 MHz
10.05
–
()
1 0.00375
–
()
×
------------------------------------------------------------------------------------------------ 1.586ms
=
相關PDF資料
PDF描述
P51-300-A-Y-D-4.5V-000-000 SENSOR 300PSI 7/16-20-2B .5-4.5V
P51-15-G-UCA-MD-5V-000-000 SENSOR 15PSI 7/16-20UNF 1-5V
P51-50-S-H-P-20MA-000-000 SENSOR 50PSIS M12 4-20 MA
P51-1000-A-S-D-4.5OVP-000-000 SENSOR 1000PSI 1/4-18NPT .5-4.5V
DSPIC33FJ32GP202T-I/SO IC DSPIC MCU/DSP 32K 28SOIC
相關代理商/技術參數
參數描述
dsPIC33FJ16GS402-50I/MM 功能描述:數字信號處理器和控制器 - DSP, DSC 16B MCU/DSP 50MIPS 16KB FL SMPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ16GS402-50I/SO 功能描述:數字信號處理器和控制器 - DSP, DSC 16B MCU/DSP 50MIPS 16KB FL SMPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ16GS402-50I/SP 功能描述:數字信號處理器和控制器 - DSP, DSC 16B MCU/DSP 50MIPS 16KB FL SMPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ16GS402-E/MM 功能描述:數字信號處理器和控制器 - DSP, DSC 16B MCU/DSP 28 LD 40MIPS 16 KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ16GS402-E/SO 功能描述:數字信號處理器和控制器 - DSP, DSC 16B MCU/DSP 28 LD 40MIPS 16 KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*