參數資料
型號: EE-SPX743
元件分類: 開關
英文描述: 3.6 mm SLOT WIDTH, 1 CHANNEL SLOTTED OPTICAL SWITCH LOGIC OUTPUT
文件頁數: 5/6頁
文件大?。?/td> 281K
代理商: EE-SPX743
EE-SPX74/84
EE-SPX74/84
5
Precautions
J INSTALLATION CONNECTIONS
Do not connect the EE-SPX to an AC (100 VAC) power supply.
Doing so may cause ignition, burning, or other damage.
Sensor
Load
Brown
Black
Blue
Do not use the EE-SPX at voltages exceeding the rated voltage
range. Doing so may cause the EE-SPX to be damaged or
burned.
Wire the EE-SPX correctly with the correct polarity. Failure to do
so may cause the EE-SPX to be damaged or burned.
Sensor
Load
Brown
Black
Blue
Do not short-circuit the load (i.e., do not connect a power supply
directly to the Sensor) as shown below. Doing so may cause the
EE-SPX to be damaged or burned.
Sensor
Load
Brown
Black
Blue
Load
short-circuiting
J CORRECT DESIGN SETUP
Cable Extensions
Use a cable with a minimum wiring cross-section surface area of
0.15 mm2 and no greater than 4 m in length. If the wiring
exceeds 4 m, connect a 10
F capacitor within the 4 m mark, as
shown in the diagram. (Use a condenser with a withstand
pressure of at least twice the sensor power source voltage.)
5 to 24 VDC
Capacitor
10
F min.
4 m max.
Extension cable
0 V
Power Source
When using a switching regulator on general sale, take the
following countermeasures.
1.
Connect a 0 V line to the power source near the sensor to
reduce impedance from the mounting, so as to prevent in-
duction noise in the vicinity of the sensor. Also, connect the
line via a capacitor (up to 0.47
F).
Mounting base
Sensor
Switching
power source
(0.47
F)
0 V
2.
Connect a noise filter terminal (middle point terminal to ACG)
for the switching power source to the body of equipment (FG)
for the power source and the 0 V.
A more stable operation can be obtained by connecting the
already-connected line to ground or to the mounting (as
recommended by all power source manufacturers).
Sensor
Mounting base
To power
source
To sensor
Switching power source
Input
Ground
0 V
3.
Insert a plastic insulator about 10 mm thick between the sen-
sor and the mounting.
Effects of Induced Noise
If there is induced noise in the (metal) mounting of the sensor, it
may cause an effect similar to light ON in the sensor. In such a
case, connect the photomicrosensor 0 V terminal and the (metal)
mounting at the same electric potential. Also, connect the
0 V terminal and the metal mounting via a 0.47
F capacitor.
Sensor
Mounting base
Power source
5 to 24 VDC
0 V
0.47
F
0 V
相關PDF資料
PDF描述
EE-SV3-CS 3.4 mm SLOT WIDTH, 1 CHANNEL SLOTTED OPTICAL SWITCH TRANSISTOR OUTPUT
EE-SV3-D 3.4 mm SLOT WIDTH, 1 CHANNEL SLOTTED OPTICAL SWITCH TRANSISTOR OUTPUT
EE-SX2088-W1 3.4 mm SLOT WIDTH, 1 CHANNEL SLOTTED OPTICAL SWITCH DARLINGTON OUTPUT
EE-SX672R 5 mm SLOT WIDTH, 1 CHANNEL SLOTTED OPTICAL SWITCH LOGIC OUTPUT
EE-SX673A 5 mm SLOT WIDTH, 1 CHANNEL SLOTTED OPTICAL SWITCH LOGIC OUTPUT
相關代理商/技術參數
參數描述
EESPX840 制造商:OMRON AUTOMATION AND SAFETY 功能描述:OPTO SENSOR SLOT TYPE NPN LT-ON 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:3.6mmSLOT PMS NPN L-ON CONNCTR
EE-SPX840 功能描述:光學開關(透射型,光電晶體管輸出) 3.6MM SLOT PMS NPN L-ON RoHS:否 制造商:Omron Electronics 輸出設備:Phototransistor 槽寬:3.4 mm 光圈寬度:0.5 mm 集電極—發射極最大電壓 VCEO:30 V 最大集電極電流:20 mA 正向電流: 安裝風格:Through Hole 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝:
EESPX841 制造商:OMRON AUTOMATION AND SAFETY 功能描述:OPTO SENSOR SLOT TYPE NPN LT-ON 制造商:Omron Electronic Components LLC 功能描述:Photointerrupter Transmissive 5mm Photologic, Open Collector 3-Pin 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:5mmSLOT PMS NPN L-ON CONNECTOR
EE-SPX841 功能描述:光學開關(透射型,光電晶體管輸出) 5MM SLOT PMS NPN L-ON RoHS:否 制造商:Omron Electronics 輸出設備:Phototransistor 槽寬:3.4 mm 光圈寬度:0.5 mm 集電極—發射極最大電壓 VCEO:30 V 最大集電極電流:20 mA 正向電流: 安裝風格:Through Hole 最大工作溫度:+ 85 C 最小工作溫度:- 25 C 封裝:
EESPX842 制造商:OMRON AUTOMATION AND SAFETY 功能描述:OPTO SENSOR SLOT TYPE NPN LT-ON 制造商:OMRON INDUSTRIAL AUTOMATION 功能描述:3.6mmSLOT PMS NPN L-ON CONNCTR