參數資料
型號: EP4SE230F29C2
廠商: Altera
文件頁數: 35/82頁
文件大?。?/td> 0K
描述: IC STRATIX IV FPGA 230K 780FBGA
產品培訓模塊: Three Reasons to Use FPGA's in Industrial Designs
標準包裝: 3
系列: STRATIX® IV E
LAB/CLB數: 9120
邏輯元件/單元數: 228000
RAM 位總計: 17544192
輸入/輸出數: 488
電源電壓: 0.87 V ~ 0.93 V
安裝類型: 表面貼裝
工作溫度: 0°C ~ 85°C
封裝/外殼: 780-BBGA
供應商設備封裝: 780-FBGA(29x29)
Chapter 1: DC and Switching Characteristics for Stratix IV Devices
1–32
Switching Characteristics
March 2014
Altera Corporation
Stratix IV Device Handbook
Volume 4: Device Datasheet and Addendum
Digital reset pulse
width
Minimum is two parallel clock cycles
Notes to Table 1–24:
(1) The minimum reconfig_clk frequency is 2.5 MHz if the transceiver channel is configured in Transmitter Only mode. The minimum reconfig_clk
frequency is 37.5 MHz if the transceiver channel is configured in Receiver only or Receiver and Transmitter mode. For more information, refer to the
(2) To calculate the REFCLK rms phase jitter requirement at reference clock frequencies other than 100 MHz, use the following formula: REFCLK rms phase
jitter at f (MHz) = REFCLK rms phase jitter at 100 MHz * 100/f.
(3) Differential LVPECL signal levels must comply to the minimum and maximum peak-to-peak differential input voltage specified in this table.
(4) The device cannot tolerate prolonged operation at this absolute maximum.
(5) You must use the 1.2-V RXVICM setting if the input serial data standard is LVDS.
(6) The differential eye opening specification at the receiver input pins assumes that Receiver Equalization is disabled. If you enable Receiver
Equalization, the receiver circuitry can tolerate a lower minimum eye opening, depending on the equalization level. Use H-Spice simulation to derive
the minimum eye opening requirement with Receiver Equalization enabled.
(7) The rate matcher supports only up to
± 300 ppm.
(8) Time taken to rx_pll_locked goes high from rx_analogreset de-assertion. Refer to Figure 1–2 on page 1–33.
(9) Time for which the CDR must be kept in lock-to-reference mode after rx_pll_locked goes high and before rx_locktodata is asserted in manual
(10) Time taken to recover valid data after the rx_locktodata signal is asserted in manual mode. Refer to Figure 1–2 on page 1–33.
(11) Time taken to recover valid data after the rx_freqlocked signal goes high in automatic mode. Refer to Figure 1–3 on page 1–33.
(12) A GPLL may be required to meet the PMA-FPGA fabric interface timing above certain data rates. For more information, refer to the “Left/Right PLL
Requirements in Basic (PMA Direct) Mode” section in the Transceiver Clocking in Stratix IV Devices chapter.
(13) The Quartus II software automatically selects the appropriate slew rate depending on the configured data rate or functional mode.
(14) For applications that require low transmit lane-to-lane skew, use Basic (PMA Direct) xN to achieve PMA-Only bonding across all channels in the link.
You can bond all channels on one side of the device by configuring them in Basic (PMA Direct) xN mode. For more information about clocking
requirements in this mode, refer to the “Basic (PMA Direct) Mode Clocking” section in the Transceiver Clocking in Stratix IV Devices chapter.
(15) If your design uses more than one dynamic reconfiguration controller (altgx_reconfig) instances to control the transceiver (altgx) channels
physically located on the same side of the device AND if you use different reconfig_clk sources for these altgx_reconfig instances, the delta
time between any two of these reconfig_clk sources becoming stable must not exceed the maximum specification listed.
(16) To support data rates lower than 600-Mbps specification through oversampling, use the CDR in LTR mode only.
Table 1–24. Transceiver Specifications for Stratix IV GT Devices (Part 8 of 8)
Symbol/
Description
Conditions
–1 Industrial Speed
Grade
–2 Industrial Speed
Grade
–3 Industrial Speed
Grade
Unit
Min
Typ
Max
Min
Typ
Max
Min
Typ
Max
相關PDF資料
PDF描述
ACC50DRTI-S93 CONN EDGECARD 100PS DIP .100 SLD
93C66BT-I/MNY IC EEPROM SER 4K 4.5V 8TDFN
93C66AT-I/MNY IC EEPROM SER 4K 4.5V 8TDFN
AMC35DRTH-S93 CONN EDGECARD 70POS DIP .100 SLD
EP2S180F1508C5 IC STRATIX II FPGA 180K 1508-FBG
相關代理商/技術參數
參數描述
EP4SE230F29C2N 功能描述:FPGA - 現場可編程門陣列 FPGA - Stratix IV E 9120 LABs 488 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EP4SE230F29C3 功能描述:FPGA - 現場可編程門陣列 FPGA - Stratix IV E 9120 LABs 488 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EP4SE230F29C3N 功能描述:FPGA - 現場可編程門陣列 FPGA - Stratix IV E 9120 LABs 488 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EP4SE230F29C4 功能描述:FPGA - 現場可編程門陣列 FPGA - Stratix IV E 9120 LABs 488 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256
EP4SE230F29C4N 功能描述:FPGA - 現場可編程門陣列 FPGA - Stratix IV E 9120 LABs 488 IOs RoHS:否 制造商:Altera Corporation 系列:Cyclone V E 柵極數量: 邏輯塊數量:943 內嵌式塊RAM - EBR:1956 kbit 輸入/輸出端數量:128 最大工作頻率:800 MHz 工作電源電壓:1.1 V 最大工作溫度:+ 70 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-256