- 您現在的位置：買賣IC網 > PDF目錄19915 > EPC8QI100 (Altera)IC CONFIG DEVICE 8MBIT 100-PQFP PDF資料下載
參數資料
| 型號： | EPC8QI100 |
| 廠商： | Altera |
| 文件頁數： | 17/36頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC CONFIG DEVICE 8MBIT 100-PQFP |
| 產品培訓模塊： | Three Reasons to Use FPGA's in Industrial Designs |
| 標準包裝： | 66 |
| 系列： | EPC |
| 可編程類型： | 系統內可編程 |
| 存儲容量： | 8Mb |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 100-BQFP |
| 供應商設備封裝： | 100-PQFP（14x20） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 604 (CN2011-ZH PDF) |
| 其它名稱： | 544-1239 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Page 24
Pin Description
Enhanced Configuration (EPC) Devices Datasheet
January 2012
Altera Corporation
WP#
Input
Usually tied to VCC or GND on the board. The controller does not drive this pin
because it could cause contention.
Connection to VCC is recommended for faster block erase or programming times
and to allow programming of the flash-bottom boot block, which is required when
programming the device using the Quartus II software.
This pin should be connected to VCC even when the external flash interface is not
used.
VCCW
Supply
Block erase, full-chip erase, word write, or lock-bit configuration power supply.
Connect this pin to the 3.3-V VCC supply, even when you are not using the external
flash interface.
RY/BY#
Open-Drain Output
Flash asserts this pin when a write or erase operation is complete. This pin is not
connected to the controller. RY/BY# is only available in Sharp flash-based EPC8
and EPC16. (2)
Leave this pin floating when the external flash interface is not used.
BYTE#
Input
Flash byte-enable pin and is only available for EPC devices in the 100-pin PQFP
package.
This pin must be connected to VCC on the board even when you are not using the
external flash interface (the controller uses the flash in 16-bit mode). For Intel
flash-based EPC device, this pin is connected to the VCCQ of the Intel flash die
internally. Therefore, BYTE# must be connected directly to VCC without using any
pull-up resistor.
Notes to Table 9:
(1) These pins can be driven to 12 V during production testing of the flash memory. Since the controller cannot tolerate the 12-V level, connections
from the controller to these pins are not made internal to the package. Instead they are available as two separate pins. You must connect the
two pins at the board level (for example, on the PCB, connect the C-WE# pin from controller to F-WE# pin from the flash memory).
(2) For more information, refer to the PCN0506: Addition of Intel Flash Memory As Source For EPC4, EPC8 and EPC16 Enhanced Configuration
Devices and Using the Intel Flash Memory-Based EPC4, EPC8 and EPC16 white paper.
Table 10. JTAG Interface Pins and Other Required Controller Pins (Part 1 of 2)
Pin Name
Pin Type
Description
TDI
Input
JTAG data input pin.
Connect this pin to VCC if the JTAG circuitry is not used.
TDO
Output
JTAG data output pin.
Do not connect this pin if the JTAG circuitry is not used (leave this pin floating).
TCK
Input
JTAG clock pin.
Connect this pin to GND if the JTAG circuitry is not used.
TMS
Input
JTAG mode select pin.
Connect this pin to VCC if the JTAG circuitry is not used.
PGM[2..0]
Input
These three input pins select one of the eight pages of configuration data to
configure the FPGAs in the system.
Connect these pins on the board to select the page specified in the Quartus II
software when generating the EPC device POF. PGM[2] is the MSB. The default
selection is page 0; PGM[2..0]=000. These pins must not be left floating.
Table 9. External Flash Interface Pins (Part 2 of 2)
Pin Name
Pin Type
Description
相關PDF資料 |
PDF描述 |
|---|---|
| NCV8506D2T50R4G | IC REG LDO 5V .4A D2PAK-7 |
| T95R336K035LZSS | CAP TANT 33UF 35V 10% 2824 |
| TNY277GN-TL | IC OFFLINE SWIT OVP OTP HV 8SMD |
| VE-J6M-CY-B1 | CONVERTER MOD DC/DC 10V 50W |
| T95D127M010EBAL | CAP TANT 120UF 10V 20% 2917 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EPC8QI100N | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 8Mb 50 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC8XXX | 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC-9 | 制造商:Curtis Industries 功能描述: 制造商:Curtis Industries 功能描述:Conn Barrier Strip 9 POS 9.52mm Solder ST Thru-Hole 15A |
| EPC9001 | 功能描述:BOARD DEV FOR EPC2015 40V GAN RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:eGaN® 標準包裝:1 系列:- 主要目的:數字電位器 嵌入式:- 已用 IC / 零件:AD5258 主要屬性:- 次要屬性:- 已供物品:板 相關產品:AD5258BRMZ1-ND - IC POT DGTL I2C1K 64P 10MSOPAD5258BRMZ10-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ100-ND - IC POT DGTL I2C 100K 64P 10MSOPAD5258BRMZ50-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ1-R7-ND - IC POT DGTL I2C 1K 64P 10MSOPAD5258BRMZ10-R7-ND - IC POT DGTL I2C 10K 64P 10MSOPAD5258BRMZ50-R7-ND - IC POT DGTL I2C 50K 64P 10MSOPAD5258BRMZ100-R7-ND - IC POT DGTL I2C 100K 64P 10MSOP |
| EPC9001C | 功能描述:EPC2015C eGaN? Series Power Management, Half H-Bridge Driver (External FET) Evaluation Board 制造商:epc 系列:eGaN? 零件狀態:有效 主要用途:電源管理，半 H 橋驅動器（外部 FET） 嵌入式:否 使用的 IC/零件:EPC2015C 主要屬性:- 輔助屬性:- 所含物品:板 標準包裝:1 |
發布緊急采購，3分鐘左右您將得到回復。