Notes to tables: (1) See the Operating Requirements for Altera De" />
參數資料
型號: EPM7128STC100-10N
廠商: Altera
文件頁數: 21/66頁
文件大小: 0K
描述: IC MAX 7000 CPLD 128 100-TQFP
標準包裝: 270
系列: MAX® 7000
可編程類型: 系統內可編程
最大延遲時間 tpd(1): 10.0ns
電壓電源 - 內部: 4.75 V ~ 5.25 V
邏輯元件/邏輯塊數目: 8
宏單元數: 128
門數: 2500
輸入/輸出數: 84
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 100-TQFP
供應商設備封裝: 100-TQFP(14x14)
包裝: 托盤
產品目錄頁面: 604 (CN2011-ZH PDF)
其它名稱: 544-2045
EPM7128STC100-10N-ND
28
Altera Corporation
MAX 7000 Programmable Logic Device Family Data Sheet
Notes to tables:
(1)
(2)
Minimum DC input voltage on I/O pins is –0.5 V and on 4 dedicated input pins is –0.3 V. During transitions, the
inputs may undershoot to –2.0 V or overshoot to 7.0 V for input currents less than 100 mA and periods shorter than
20 ns.
(3)
Numbers in parentheses are for industrial-temperature-range devices.
(4)
VCC must rise monotonically.
(5)
The POR time for all 7000S devices does not exceed 300 μs. The sufficient VCCINT voltage level for POR is 4.5 V. The
device is fully initialized within the POR time after VCCINT reaches the sufficient POR voltage level.
(6)
3.3-V I/O operation is not available for 44-pin packages.
(7)
The VCCISP parameter applies only to MAX 7000S devices.
(8)
During in-system programming, the minimum DC input voltage is –0.3 V.
(9)
These values are specified under the MAX 7000 recommended operating conditions in Table 14 on page 26.
(10) The parameter is measured with 50% of the outputs each sourcing the specified current. The IOH parameter refers
to high-level TTL or CMOS output current.
(11) The parameter is measured with 50% of the outputs each sinking the specified current. The IOL parameter refers to
low-level TTL, PCI, or CMOS output current.
(12) When the JTAG interface is enabled in MAX 7000S devices, the input leakage current on the JTAG pins is typically
–60 μA.
(13) Capacitance is measured at 25° C and is sample-tested only. The OE1 pin has a maximum capacitance of 20 pF.
Figure 11 shows the typical output drive characteristics of MAX 7000
devices.
Figure 11. Output Drive Characteristics of 5.0-V MAX 7000 Devices
Timing Model
MAX 7000 device timing can be analyzed with the Altera software, with a
variety of popular industry-standard EDA simulators and timing
analyzers, or with the timing model shown in Figure 12. MAX 7000
devices have fixed internal delays that enable the designer to determine
the worst-case timing of any design. The Altera software provides timing
simulation, point-to-point delay prediction, and detailed timing analysis
for a device-wide performance evaluation.
VO Output Voltage (V)
12345
30
60
90
150
120
VCCIO = 3.3 V
IOL
IOH
Room Temperature
3.3
VO Output Voltage (V)
12345
30
60
90
150
120
VCCIO = 5.0 V
IOL
IOH
Room Temperature
I O
Typical
Output
Current (mA)
I O
Typical
Output
Current (mA)
相關PDF資料
PDF描述
ISPLSI 1032EA-100LT100 IC PLD ISP 64I/O 10NS 100TQFP
VI-27N-CY-F3 CONVERTER MOD DC/DC 18.5V 50W
TAP104K050CRW CAP TANT 0.1UF 50V 10% RADIAL
RW2-0515S/H2 CONV DC/DC 2W 4.5-9VIN 15VOUT
VI-J1F-CW-B1 CONVERTER MOD DC/DC 72V 100W
相關代理商/技術參數
參數描述
EPM7128STC10015 制造商:Altera Corporation 功能描述:
EPM7128STC100-15 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX 7000 128 Macro 84 IOs RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
EPM7128STC100-15F 功能描述:IC MAX 7000 CPLD 128 100-TQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - CPLD(復雜可編程邏輯器件) 系列:MAX® 7000 標準包裝:24 系列:CoolRunner II 可編程類型:系統內可編程 最大延遲時間 tpd(1):7.1ns 電壓電源 - 內部:1.7 V ~ 1.9 V 邏輯元件/邏輯塊數目:24 宏單元數:384 門數:9000 輸入/輸出數:173 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:208-BFQFP 供應商設備封裝:208-PQFP(28x28) 包裝:托盤
EPM7128STC100-15N 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX 7000 128 Macro 84 IOs RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100
EPM7128STC100-6 功能描述:CPLD - 復雜可編程邏輯器件 CPLD - MAX 7000 128 Macro 84 IOs RoHS:否 制造商:Lattice 系列: 存儲類型:EEPROM 大電池數量:128 最大工作頻率:333 MHz 延遲時間:2.7 ns 可編程輸入/輸出端數量:64 工作電源電壓:3.3 V 最大工作溫度:+ 90 C 最小工作溫度:0 C 封裝 / 箱體:TQFP-100