參數資料
型號： EVAL-AD5110SDZ
廠商： Analog Devices Inc
文件頁數： 16/28頁
文件大?。?/td> 0K
描述： BOARD EVAL FOR AD5110
標準包裝： 1
主要目的： 數字電位器
嵌入式： 否
已用 IC / 零件： AD5110
主要屬性： 1 通道，128 位置
次要屬性： I²C 接口
已供物品： 板，CD
Data Sheet
AD5110/AD5112/AD5114
Rev. B | Page 23 of 28
EEPROM WRITE ACKNOWLEGDE POLLING
After each write operation to the EEPROM, an internal write
cycle begins. The I2C interface of the device is disabled. To
determine if the internal write cycle is complete and the I2C
interface is enabled, interface polling can be executed. I2C
interface polling can be conducted by sending a start condition,
followed by the slave address and the write bit. If the I2C
interface responds with an acknowledge, the write cycle is
complete, and the interface is ready to proceed with further
operations. Otherwise, I2C interface polling can be repeated
until it succeeds.
READ OPERATION
The AD5110/AD5112/AD5114 allow read back of the contents
of the RDAC register and EEPROM memory through the I2C
interface by using Command 6 (see Table 10).
When reading data back from the AD5110/AD5112/AD5114,
the user must first issue a readback command to the device.
This begins with a start command, followed by an address
byte (R/W = 0), after which the AD5110/AD5112/AD5114
acknowledges that it is prepared to receive data by pulling
SDA low.
Two bytes of data are then written to the AD5110/AD5112/
AD5114, the most significant byte followed by the least
significant byte. Both of these data bytes are acknowledged by
the AD5110/AD5112/AD5114. A stop condition follows. These
bytes contain the read instruction, which enables readback of
the RDAC register, EEPROM memory. The user can then read
back the data. This begins with a start command followed by an
address byte (R/W = 1), after which the device acknowledges
that it is prepared to transmit data by pulling SDA low. Two
bytes of data are then read from the device, which are both
acknowledged by the master, as shown in Figure 45. A stop
condition follows. If the master does not acknowledge the first
byte, then the second byte is not transmitted by the AD5110/
The AD5110/AD5112/AD5114 does not support repeat
readback.
RESET
The AD5110/AD5112/AD5114 can be reset by executing
Command 4 (see Table 10). The reset command loads the
RDAC register with the contents of the EEPROM and takes
approximately 25 s. EEPROM is pre-loaded to midscale at the
factory, and initial power-up is, accordingly, at midscale.
SHUTDOWN MODE
The AD5110/AD5112/AD5114 can be shut down by executing
the software shutdown command, Command 3 (see Table 10).
This feature places the RDAC in a zero-power-consumption
state where Terminal A is open-circuited and the wiper,
Terminal W is connected to Terminal B but a finite wiper
resistance of 45 Ω is present. The part can be taken out of
shutdown mode by executing Command 3 (see Table 10)
and setting Bit DB0 to 0.
SCL
SDA
START BY
MASTER
ACK. BY
AD5110
ACK. BY
AD5110
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
MOST SIGNIFICANT DATA BYTE
FRAME 3
LEAST SIGNIFICANT DATA BYTE
SCL (CONTINUED)
SDA (CONTINUED)
ACK. BY
AD5110
STOP BY
MASTER
STOP BY
MASTER
0
1
9
1
9
1
0
1
A1
A0
0
C2
C1
C0
D4
D3
D5
D7
D6
D2
D1
D0
R/W
SCL
SDA
START BY
MASTER
ACK. BY
AD5110
NO ACK.
BY MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
MOST SIGNIFICANT DATA BYTE
0
1
9
1
0
1
A1
A0
D7
D6
D5
D4
D3
D2
D1
D0
R/W
09582-
045
Figure 45. AD5110 Interface Read Command
相關PDF資料
PDF描述
RBC13DREN-S93 CONN EDGECARD 26POS .100 EXTEND
837655-9 CONN LEAD ASSY 16AWG SGL-END 20"
EET-UQ2D561JA CAP ALUM 560UF 200V 20% SNAP
EVAL-AD8403SDZ BOARD EVAL FOR AD8403
EEM25DRST CONN EDGECARD 50POS DIP .156 SLD
相關代理商/技術參數
參數描述
EVAL-AD5111SDZ 功能描述:BOARD EVAL FOR AD5111 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
EVAL-AD5116EBZ 功能描述:BOARD EVAL FOR AD5116 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:* 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081
EVAL-AD5141DBZ 功能描述:數字電位計開發工具 EVALUATION BOARD I.C. RoHS:否 制造商:Arduino 產品:TinkerKit Rotary Potentiometers 工具用于評估:TinkerKit 電阻:4.7 kOhms 工作電源電壓:0 V to 5 V
EVAL-AD5142ADBZ 功能描述:數字電位計開發工具 EVALUATION BOARD I.C. RoHS:否 制造商:Arduino 產品:TinkerKit Rotary Potentiometers 工具用于評估:TinkerKit 電阻:4.7 kOhms 工作電源電壓:0 V to 5 V
EVAL-AD5142DBZ 功能描述:數字電位計開發工具 EVALUATION BOARD I.C. RoHS:否 制造商:Arduino 產品:TinkerKit Rotary Potentiometers 工具用于評估:TinkerKit 電阻:4.7 kOhms 工作電源電壓:0 V to 5 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*