參數資料
型號： EVAL-AD7323CBZ
廠商： Analog Devices Inc
文件頁數： 7/37頁
文件大小： 0K
描述： BOARD EVALUATION FOR AD7323CBZ
標準包裝： 1
系列： iCMOS®
ADC 的數量： 1
位數： 12
采樣率（每秒）： 500k
數據接口： 串行
輸入范圍： ±10 V
在以下條件下的電源（標準）： 17mW @ 500kSPS
工作溫度： -40°C ~ 85°C
已用 IC / 零件： AD7323
已供物品： 板
相關產品： AD7323BRUZ-REEL-ND - IC ADC 12BIT+SAR 4CHAN 16-TSSOP
AD7323BRUZ-REEL7-ND - IC ADC 12BIT+ SAR 4CHAN 16TSSOP
AD7323BRUZ-ND - IC ADC 12BIT+ SAR 4CHAN 16TSSOP
AD7323
Data Sheet
Rev. B | Page 14 of 36
TERMINOLOGY
Differential Nonlinearity
This is the difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
Integral Nonlinearity
This is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale (a point 1 LSB
below the first code transition) and full scale (a point 1 LSB
above the last code transition).
Offset Code Error
This applies to straight binary output coding. It is the deviation
of the first code transition (00…000) to (00…001) from the
ideal, that is, AGND + 1 LSB.
Offset Error Match
This is the difference in offset error between any two input
channels.
Gain Error
This applies to straight binary output coding. It is the deviation
of the last code transition (111…110) to (111…111) from the
ideal (that is, 4 × VREF 1 LSB, 2 × VREF 1 LSB, VREF 1 LSB)
after adjusting for the offset error.
Gain Error Match
This is the difference in gain error between any two input
channels.
Bipolar Zero Code Error
This applies when using twos complement output coding and a
bipolar analog input. It is the deviation of the midscale transi-
tion (all 1s to all 0s) from the ideal input voltage, that is, AGND
1 LSB.
Bipolar Zero Code Error Match
This refers to the difference in bipolar zero code error between
any two input channels.
Positive Full-Scale Error
This applies when using twos complement output coding and
any of the bipolar analog input ranges. It is the deviation of the
last code transition (011…110) to (011…111) from the ideal
(4 × VREF 1 LSB, 2 × VREF 1 LSB, VREF 1 LSB) after adjusting
for the bipolar zero code error.
Positive Full-Scale Error Match
This is the difference in positive full-scale error between any
two input channels.
Negative Full-Scale Error
This applies when using twos complement output coding and
any of the bipolar analog input ranges. This is the deviation of
the first code transition (10…000) to (10…001) from the ideal
(that is, 4 × VREF + 1 LSB, 2 × VREF + 1 LSB, VREF + 1 LSB)
after adjusting for the bipolar zero code error.
Negative Full-Scale Error Match
This is the difference in negative full-scale error between any
two input channels.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns into track mode after the
14th SCLK rising edge. Track-and-hold acquisition time is the
time required for the output of the track-and-hold amplifier to
reach its final value, within ± LSB, after the end of a conversion.
For the ±2.5 V range, the specified acquisition time is the time
required for the track-and-hold amplifier to settle to within ±1 LSB.
Signal-to-(Noise + Distortion) Ratio
This is the measured ratio of signal-to-(noise + distortion) at
the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent on the number of quantization levels in the digitization
process. The more levels there are, the smaller the quantization
noise becomes. Theoretically, the signal-to-(noise + distortion)
ratio for an ideal N-bit converter with a sine wave input is given by
Signal-to-(Noise + Distortion) = (6.02 N + 1.76) dB
For a 13-bit converter, this is 80.02 dB.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
harmonics to the fundamental. For the AD7323, it is defined as
1
2
6
2
5
2
4
2
3
2
log
20
)
dB
(
V
THD
+
=
where V1 is the rms amplitude of the fundamental, and V2, V3,
V4, V5, and V6 are the rms amplitudes of the second through the
sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic or spurious noise is defined as the ratio of the
rms value of the next largest component in the ADC output
spectrum (up to fS/2, excluding dc) to the rms value of the
fundamental. Normally, the value of this specification is
determined by the largest harmonic in the spectrum, but for
ADCs where the harmonics are buried in the noise floor, the
largest harmonic can be a noise peak.
相關PDF資料
PDF描述
VI-B6N-EY CONVERTER MOD DC/DC 18.5V 50W
ABC07DREF CONN EDGECARD 14POS .100 EYELET
ECC50DJWN CONN EDGECARD 100POS .100X.200
VI-B6M-EY CONVERTER MOD DC/DC 10V 50W
EVAL-AD7725CBZ BOARD EVALUATION FOR AD7725
相關代理商/技術參數
參數描述
EVAL-AD7324CB 制造商:AD 制造商全稱:Analog Devices 功能描述:4-Channel, Software-Selectable, True Bipolar Input, 12-Bit Plus Sign ADC
EVAL-AD7324CBZ 功能描述:BOARD EVALUATION FOR AD7324CBZ RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:iCMOS® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7327CB 制造商:AD 制造商全稱:Analog Devices 功能描述:500 kSPS, 8-Channel, Software-Selectable, True Bipolar Input, 12-Bit Plus Sign ADC
EVAL-AD7327CBZ 功能描述:BOARD EVALUATION FOR AD7327 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:iCMOS® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7327SDZ 功能描述:BOARD EVAL FOR AD7327SDZ RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*