- 您現在的位置：買賣IC網 > PDF目錄17060 > EVAL-AD7356EDZ (Analog Devices Inc)BOARD EVAL AD7356 PDF資料下載
參數資料
| 型號： | EVAL-AD7356EDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/21頁 |
| 文件大小： | 0K |
| 描述： | BOARD EVAL AD7356 |
| 標準包裝： | 1 |
| ADC 的數量： | 2 |
| 位數： | 12 |
| 采樣率（每秒）： | 5M |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF/2 |
| 在以下條件下的電源（標準）： | 36mW @ 5MSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7356 |
| 已供物品： | 板，CD |
AD7356
Rev. A | Page 7 of 20
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
VINA–
REFA
REFGND
VINB–
REFB
AGND
VINA+
VINB+
16
15
14
13
12
11
10
9
SCLK
SDATAA
SDATAB
CS
VDD
AGND
DGND
VDRIVE
AD7356
TOP VIEW
(Not to Scale)
06
50
5-
0
02
Figure 2. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
Mnemonic
Description
1, 2
VINA+, VINA
Analog Inputs of ADC A. These analog inputs form a fully differential pair.
3, 6
REFA, REFB
Reference Decoupling Capacitor Pins. Decoupling capacitors are connected between these pins and the
REFGND pin to decouple the reference buffer for each respective ADC. It is recommended to decouple each
reference pin with a 10 μF capacitor. Provided the output is buffered, the on-chip reference can be taken from
these pins and applied externally to the rest of the system. The nominal internal reference voltage is 2.048 V
and appears at these pins. These pins can also be overdriven by an external reference. The input voltage range
for the external reference is 2.048 V + 100 mV to VDD.
4
REFGND
Reference Ground. This is the ground reference point for the reference circuitry on the AD7356. Refer any
external reference signal to this REFGND voltage. Decoupling capacitors must be placed between this pin and
the REFA and REFB pins. Connect the REFGND pin to the AGND plane of a system.
5, 11
AGND
Analog Ground. This is the ground reference point for all analog circuitry on the AD7356. All analog input
signals should be referred to this AGND voltage. The AGND and DGND voltages should ideally be at the same
potential and must not be more than 0.3 V apart, even on a transient basis.
7, 8
VINB, VINB+
Analog Inputs of ADC B. These analog inputs form a fully differential pair.
9
VDD
Power Supply Input. The VDD range for the AD7356 is 2.5 V ± 10%. Decouple the supply to AGND with a 0.1 μF
capacitor in parallel with a 10 μF tantalum capacitor.
10
CS
Chip Select. Active low logic input. This input provides the dual functions of initiating conversions on the
AD7356 and framing the serial data transfer.
12
DGND
Digital Ground. This is the ground reference point for all digital circuitry on the AD7356. Connect this pin to
the DGND plane of a system. The DGND and AGND voltages should ideally be at the same potential and must
not be more than 0.3 V apart, even on a transient basis.
13, 14
SDATAB, SDATAA
Serial Data Outputs. The data output is supplied to each pin as a serial data stream. The bits are clocked out
on the falling edge of the SCLK input. To access the 12 bits of data from the AD7356, 14 SCLK falling edges are
required. The data simultaneously appears on both data output pins from the simultaneous conversions of
both ADCs. The data stream consists of two leading zeros followed by the 12 bits of conversion data. The data
is provided MSB first. If CS is held low for 16 SCLK cycles rather than 14 on the AD7356, then two trailing zeros
appear after the 12 bits of data. If CS is held low for a further 16 SCLK cycles on either SDATA or SDATAB, the
data from the other ADC follows on the SDATA pins. This allows data from a simultaneous conversion on both
ADCs to be gathered in serial format on either SDATAA or SDATAB.
A
15
SCLK
Serial Clock. Logic input. A serial clock input provides the serial clock for accessing the data from the AD7356.
This clock is also used as the clock source for the conversion process.
16
VDRIVE
Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the interface operates.
The voltage at this pin may be different than the voltage at VDD. The VDRIVE supply should be decoupled to
DGND with a 0.1 μF capacitor in parallel with a 10 μF tantalum capacitor.
相關PDF資料 |
PDF描述 |
|---|---|
| MIC2009YM6 TR | IC DISTRIBUTION SW ADJ SOT23-6 |
| 0210391030 | CABLE JUMPER 1MM .030M 33POS |
| EVAL-AD7352EDZ | BOARD EVAL AD7352 |
| 0210390949 | CABLE JUMPER 1MM .102M 25POS |
| 0210390948 | CABLE JUMPER 1MM .102M 25POS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7357EDZ | 功能描述:BOARD EVAL FOR AD7357 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7366CBZ | 功能描述:BOARD EVALUATION FOR AD7366 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:iCMOS® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7366SDZ | 功能描述:BOARD EVAL FOR AD7366 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:iCMOS® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7367CBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:True Bipolar Input, Dual 1 レs, 12-/14-Bit, 2-Channel SAR ADCs |
| EVAL-AD7367SDZ | 功能描述:數據轉換 IC 開發工具 EVALUATION CONTROL BOARD I.C. RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
發布緊急采購，3分鐘左右您將得到回復。