- 您現在的位置：買賣IC網 > PDF目錄17049 > EVAL-AD7357EDZ (Analog Devices Inc)BOARD EVAL FOR AD7357 PDF資料下載
參數資料
| 型號： | EVAL-AD7357EDZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 20/21頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD7357 |
| 標準包裝： | 1 |
| ADC 的數量： | 2 |
| 位數： | 14 |
| 采樣率（每秒）： | 4.2M |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF/2 |
| 在以下條件下的電源（標準）： | 36mW @ 4.2MSPS |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7357 |
| 已供物品： | 板，CD |
AD7357
Rev. B | Page 7 of 20
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
VINA–
REFA
REFGND
VINB–
REFB
AGND
VINA+
VINB+
16
15
14
13
12
11
10
9
SCLK
SDATAA
SDATAB
CS
VDD
AGND
DGND
VDRIVE
AD7357
TOP VIEW
(Not to Scale)
07
75
7-
0
02
Figure 2. Pin Configuration
Table 5. Pin Function Descriptions
Pin No.
Mnemonic
Description
1, 2
VINA+, VINA
Analog Inputs of ADC A. These analog inputs form a fully differential pair.
3, 6
REFA, REFB
Reference Decoupling Capacitor Pins. Decoupling capacitors are connected between these pins and the
REFGND pin to decouple the reference buffer for each respective ADC. It is recommended to decouple each
reference pin with a 10 μF capacitor. Provided that the output is buffered, the on-chip reference can be taken
from these pins and applied externally to the rest of the system. The nominal internal reference voltage is
2.048 V and appears at these pins. These pins can also be overdriven by an external reference. The input
voltage range for the external reference is 2.048 V + 100 mV to VDD.
4
REFGND
Reference Ground. This is the ground reference point for the reference circuitry on the AD7357. Any external
reference signal should be referred to this REFGND voltage. Decoupling capacitors must be placed between
this pin and the REFA and REFB pins.
5, 11
AGND
Analog Ground. This is the ground reference point for all analog circuitry on the AD7357. All analog input
signals should be referred to this AGND voltage. The AGND and DGND voltages should ideally be at the same
potential and must not be more than 0.3 V apart, even on a transient basis.
7, 8
VINB, VINB+
Analog Inputs of ADC B. These analog inputs form a fully differential pair.
9
VDD
Power Supply Input. The VDD range for the AD7357 is 2.5 V ± 10%. The supply should be decoupled to AGND
with a 0.1 μF capacitor and a 10 μF tantalum capacitor.
10
CS
Chip Select. Active low, logic input. This input provides the dual function of initiating conversions on the
AD7357 and framing the serial data transfer.
12
DGND
Digital Ground. This is the ground reference point for all digital circuitry on the AD7357. This pin should
connect to the DGND plane of a system. The DGND and AGND voltages should ideally be at the same potential
and must not be more than 0.3 V apart, even on a transient basis.
13, 14
SDATAB, SDATAA
Serial Data Outputs. The data output is supplied to each pin as a serial data stream. The bits are clocked out on
the falling edge of the SCLK input. 16 SCLK falling edges are required to access the 14 bits of data from the
AD7357. The data simultaneously appears on both data output pins from the simultaneous conversions of
both ADCs. The data stream consists of two leading zeros, followed by the 14 bits of conversion data. The data
is provided MSB first. If CS is held low for 18 SCLK cycles rather than 16, then two trailing zeros appear after the
14 bits of data. If CS is held low for an additional 18 SCLK cycles on either SDATA or SDATAB , the data from the
other ADC follows on the SDATA pins. This allows data from a simultaneous conversion on both ADCs to be
gathered in serial format on either SDATA or SDATAB.
A
15
SCLK
Serial Clock. Logic input. A serial clock input provides the SCLK for accessing the data from the AD7357. This
clock is also used as the clock source for the conversion process.
16
VDRIVE
Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the interface operates.
This pin should be decoupled to DGND. The voltage at this pin may be different to that at VDD.
相關PDF資料 |
PDF描述 |
|---|---|
| ECE-A0JKG220 | CAP ALUM 22UF 6.3V 20% RADIAL |
| GEM25DTAH | CONN EDGECARD 50POS R/A .156 SLD |
| STD09W-Q | WIRE & CABLE MARKERS |
| ISL5761EVAL1 | EVALUATION PLATFORM ISL5761 SOIC |
| STD02W-M | WIRE & CABLE MARKERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7366CBZ | 功能描述:BOARD EVALUATION FOR AD7366 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:iCMOS® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7366SDZ | 功能描述:BOARD EVAL FOR AD7366 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:iCMOS® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7367CBZ | 制造商:AD 制造商全稱:Analog Devices 功能描述:True Bipolar Input, Dual 1 レs, 12-/14-Bit, 2-Channel SAR ADCs |
| EVAL-AD7367SDZ | 功能描述:數據轉換 IC 開發工具 EVALUATION CONTROL BOARD I.C. RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| EVAL-AD7376EBZ | 功能描述:BOARD EVAL FOR AD7376 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
發布緊急采購，3分鐘左右您將得到回復。