參數資料
型號: EVAL-AD7650CBZ
廠商: Analog Devices Inc
文件頁數: 19/20頁
文件大?。?/td> 0K
描述: BOARD EVALUATION FOR AD7650
標準包裝: 1
ADC 的數量: 1
位數: 16
采樣率(每秒): 570k
數據接口: 串行,并聯
輸入范圍: ±VREF
在以下條件下的電源(標準): 150mW @ 570kSPS
工作溫度: -40°C ~ 85°C
已用 IC / 零件: AD7650
已供物品:
相關產品: AD7650ACPZ-ND - IC ADC 16BIT CMOS 5V 48LFCSP
AD7650ASTZ-ND - IC ADC 16BIT 570KSPS 48LQFP
AD7650ASTZRL-ND - IC ADC 16BIT CMOS 5V 48LQFP
AD7650ACPZRL-ND - IC ADC 16BIT CMOS 5V 48LFCSP
REV. 0
AD7650
–8–
DEFINITION OF SPECIFICATIONS
INTEGRAL NONLINEARITY ERROR (INL)
Linearity error refers to the deviation of each individual code
from a line drawn from “negative full scale” through “positive
full scale.” The point used as “negative full scale” occurs 1/2 LSB
before the first code transition. “Positive full scale” is defined as a
level 1 1/2 LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line.
DIFFERENTIAL NONLINEARITY ERROR (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It is
often specified in terms of resolution for which no missing codes
are guaranteed.
FULL-SCALE ERROR
The last transition (from 011 . . . 10 to 011 . . . 11 in two’s comple-
ment coding) should occur for an analog voltage 1 1/2 LSB below
the nominal full scale (2.49994278 V for the 0 V–2.5 V range).
The full-scale error is the deviation of the actual level of the last
transition from the ideal level.
UNIPOLAR ZERO ERROR
The first transition should occur at a level 1/2 LSB above analog
ground (19.073
V for the 0 V–2.5 V range). Unipolar zero
error is the deviation of the actual transition from that point.
SPURIOUS FREE DYNAMIC RANGE (SFDR)
The difference, in decibels (dB), between the rms amplitude of
the input signal and the peak spurious signal.
EFFECTIVE NUMBER OF BITS (ENOB)
ENOB is a measurement of the resolution with a sine wave input.
It is related to S/(N+D) by the following formula:
ENOB
S N
D
dB
=+
[]
()
176
6 02
./ .
and is expressed in bits.
TOTAL HARMONIC DISTORTION (THD)
THD is the ratio of the rms sum of the first five harmonic compo-
nents to the rms value of a full-scale input signal and is expressed
in decibels.
SIGNAL-TO-NOISE RATIO (SNR)
SNR is the ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
SIGNAL TO (NOISE + DISTORTION) RATIO (S/[N+D])
S/(N+D) is the ratio of the rms value of the actual input signal to
the rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
S/(N+D) is expressed in decibels.
APERTURE DELAY
Aperture delay is a measure of the acquisition performance and
is measured from the falling edge of the
CNVST input to when
the input signal is held for a conversion.
TRANSIENT RESPONSE
The time required for the AD7650 to achieve its rated accuracy
after a full-scale step function is applied to its input.
OVERVOLTAGE RECOVERY
The time required for the ADC to recover to full accuracy after
an analog input signal 150% of full-scale is reduced to 50% of
the full-scale value.
NOTES
AI = Analog Input
DI = Digital Input
DI/O = Bidirectional Digital
DO = Digital Output
P = Power
PIN FUNCTION DESCRIPTIONS (continued)
Pin No.
Mnemonic
Type
Description
35
CNVST
DI
Start Conversion. A falling edge on
CNVST puts the internal sample/hold into the hold state
and initiates a conversion. In impulse mode (IMPULSE HIGH and WARP LOW), if
CNVST
is held low when the acquisition phase (t8) is complete, the internal sample/hold is put into
the hold state and a conversion is immediately started.
36
AGND
P
Must Be Tied to Analog Ground
37
REF
AI
Reference Input Voltage
38
REFGND
AI
Reference Input Analog Ground
39
IN–
AI
Analog Input Ground
43
IN+
AI
Primary Analog Input with a Range of 0 V to VREF.
相關PDF資料
PDF描述
0982660864 CBL 17POS 0.5MM JMPR TYPE D 6"
AISC-0805-R39J-T INDUCTOR WW CERAM 390NH 0805
VE-JT2-EY CONVERTER MOD DC/DC 15V 50W
222A121-4-0 BOOT MOLDED
EVAL-AD7663CBZ BOARD EVALUATION FOR AD7663
相關代理商/技術參數
參數描述
EVAL-AD7650EDZ 功能描述:BOARD EVAL FOR AD7650 RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件
EVAL-AD7651CB 制造商:Analog Devices 功能描述:DEV TOOLS, 16BIT 100KSPS SAR UNIPOLAR ADC W/ REF - Bulk
EVAL-AD7651CBZ 功能描述:BOARD EVALUATION FOR AD7651 RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件
EVAL-AD7651EDZ 功能描述:BOARD EVAL FOR AD7651 RoHS:是 類別:編程器,開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率(每秒):94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源(標準):- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板,軟件
EVAL-AD7652CB 制造商:Analog Devices 功能描述:DEV TOOLS, 16BIT 500KSPS SAR UNIPOLAR ADC W/ REF - Bulk