- 您現在的位置：買賣IC網 > PDF目錄17058 > EVAL-AD7792EBZ (Analog Devices Inc)BOARD EVALUATION FOR AD7792 PDF資料下載
參數資料
| 型號： | EVAL-AD7792EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 8/33頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVALUATION FOR AD7792 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 470 |
| 數據接口： | 串行 |
| 輸入范圍： | ±VREF/增益 |
| 在以下條件下的電源（標準）： | 2.5mW @ 470SPS |
| 工作溫度： | -40°C ~ 105°C |
| 已用 IC / 零件： | AD7792 |
| 已供物品： | 板，CD |
| 相關產品： | AD7792BRU-ND - IC ADC 16BIT 3CH LP 16-TSSOP AD7792BRUZ-REEL-ND - IC ADC 16BIT 3CH LP 16-TSSOP AD7792BRUZ-ND - IC ADC 16BIT SIG-DEL 3CH 16TSSOP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
AD7792/AD7793
Rev. B | Page 15 of 32
STATUS REGISTER
RS2, RS1, RS0 = 0, 0, 0; Power-On/Reset = 0x80 (AD7792)/0x88 (AD7793)
The status register is an 8-bit read-only register. To access the ADC status register, the user must write to the communications register,
select the next operation to be a read, and load Bit RS2, Bit RS1, and Bit RS0 with 0. Table 13 outlines the bit designations for the status
register. SR0 through SR7 indicate the bit locations, and SR denotes that the bits are in the status register. SR7 denotes the first bit of the
data stream. The number in parentheses indicates the power-on/reset default status of that bit.
SR7
SR6
SR5
SR4
SR3
SR2
SR1
SR0
RDY(1)
ERR(0)
0(0)
0/1
CH2(0)
CH1(0)
CH0(0)
Table 13. Status Register Bit Designations
Bit Location
Bit Name
Description
SR7
RDY
Ready Bit for ADC. Cleared when data is written to the ADC data register. The RDY bit is set automatically
after the ADC data register has been read or a period of time before the data register is updated with a new
conversion result to indicate to the user not to read the conversion data. It is also set when the part is
placed in power-down mode. The end of a conversion is indicated by the DOUT/RDY pin also. This pin can
be used as an alternative to the status register for monitoring the ADC for conversion data.
SR6
ERR
ADC Error Bit. This bit is written to at the same time as the RDY bit. Set to indicate that the result written to
the ADC data register has been clamped to all 0s or all 1s. Error sources include overrange and underrange.
Cleared by a write operation to start a conversion.
SR5 to SR4
0
These bits are automatically cleared.
SR3
0/1
This bit is automatically cleared on the AD7792 and is automatically set on the AD7793.
SR2 to SR0
CH2 to CH0
These bits indicate which channel is being converted by the ADC.
MODE REGISTER
RS2, RS1, RS0 = 0, 0, 1; Power-On/Reset = 0x000A
The mode register is a 16-bit register from which data can be read or to which data can be written. This register is used to select the
operating mode, update rate, and clock source. Table 14 outlines the bit designations for the mode register. MR0 through MR15 indicate
the bit locations, MR denoting the bits are in the mode register. MR15 denotes the first bit of the data stream. The number in parentheses
indicates the power-on/reset default status of that bit. Any write to the setup register resets the modulator and filter and sets the RDY bit.
MR15
MR14
MR13
MR12
MR11
MR10
MR9
MR8
MD2(0)
MD1(0)
MD0(0)
0(0)
MR7
MR6
MR5
MR4
MR3
MR2
MR1
MR0
CLK1(0)
CLK0(0)
0(0)
FS3(1)
FS2(0)
FS1(1)
FS0(0)
Table 14. Mode Register Bit Designations
Bit Location
Bit Name
Description
MR15 to
MR13
MD2 to
MD0
Mode Select Bits. These bits select the operational mode of the AD7792/AD7793 (see Table 15).
MR12 to MR8
0
These bits must be programmed with a Logic 0 for correct operation.
MR7 to MR6
CLK1 to
CLK0
These bits are used to select the clock source for the AD7792/AD7793. Either an on-chip 64 kHz clock can be
used, or an external clock can be used. The ability to override using an external clock allows several
AD7792/AD7793 devices to be synchronized. In addition, 50 Hz/60 Hz is improved when an accurate external
clock drives the AD7792/AD7793.
CLK1
CLK0
ADC Clock Source
0
Internal 64 kHz Clock. Internal clock is not available at the CLK pin.
0
1
Internal 64 kHz Clock. This clock is made available at the CLK pin.
1
0
External 64 kHz Clock Used. An external clock gives better 50 Hz/60 Hz rejection. See
specifications for external clock.
1
External Clock Used. The external clock is divided by 2 within the AD7792/AD7793.
MR5 to MR4
0
These bits must be programmed with a Logic 0 for correct operation.
MR3 to MR0
FS3 to FS0
Filter Update Rate Select Bits (see Table 16).
相關PDF資料 |
PDF描述 |
|---|---|
| EEM24DRMT | CONN EDGECARD 48POS .156 WW |
| RPP20-4815S/N | CONV DC/DC 20W 36-75VIN 15VOUT |
| DEMOS08AC16KIT | KIT DEMO FOR S08AC16 FAMILY |
| RPP20-4815D/N | CONV DC/DC 20W 36-75VIN +/-15V |
| DEMOS08AC128KIT | KIT DEMO FOR S08AC128 FAMILY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7792EBZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3-Channel, Low Noise, Low Power, 16-/24-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
| EVAL-AD7793EB | 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk |
| EVAL-AD7793EBZ | 功能描述:BOARD EVALUATION FOR AD7793 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7793EBZ | 制造商:Analog Devices 功能描述:EVAL BOARD, AD7793 3CH 24BIT ADC |
| EVAL-AD7793EBZ1 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3-Channel, Low Noise, Low Power, 16-/24-Bit ?￡-?? ADC with On-Chip In-Amp and Reference |
發布緊急采購，3分鐘左右您將得到回復。