參數資料
型號： EVAL-AD7793EBZ
廠商： Analog Devices Inc
文件頁數： 18/33頁
文件大小： 0K
描述： BOARD EVALUATION FOR AD7793
標準包裝： 1
ADC 的數量： 1
位數： 24
采樣率（每秒）： 470
數據接口： 串行
輸入范圍： 0 ~ 5 V
在以下條件下的電源（標準）： 2.5mW @ 470SPS
工作溫度： -40°C ~ 105°C
已用 IC / 零件： AD7793
已供物品： 板，纜線，CD
相關產品： AD7793BRU-ND - IC ADC 24BIT 3CH LP 16-TSSOP
AD7793BRUZ-REEL-ND - IC ADC 24BIT 3CH LP 16-TSSOP
AD7793BRUZ-ND - IC ADC 24BIT SIG-DEL 3CH 16TSSOP
AD7792/AD7793
Rev. B | Page 24 of 32
CIRCUIT DESCRIPTION
ANALOG INPUT CHANNEL
The AD7792/AD7793 have three differential analog input
channels. These are connected to the on-chip buffer amplifier
when the device is operated in buffered mode and directly to
the modulator when the device is operated in unbuffered mode.
In buffered mode (the BUF bit in the mode register is set to 1),
the input channel feeds into a high impedance input stage of the
buffer amplifier. Therefore, the input can tolerate significant
source impedances and is tailored for direct connection to
external resistive-type sensors, such as strain gauges or
resistance temperature detectors (RTDs).
When BUF = 0, the part is operated in unbuffered mode.
This results in a higher analog input current. Note that this
unbuffered input path provides a dynamic load to the driving
source. Therefore, resistor/capacitor combinations on the input
pins can cause gain errors, depending on the output impedance
of the source that is driving the ADC input. Table 19 shows the
allowable external resistance/capacitance values for unbuffered
mode such that no gain error at the 20-bit level is introduced.
Table 19. External R-C Combination for No 20-Bit Gain Error
C (pF)
R (Ω)
50
9 k
100
6 k
500
1.5 k
1000
900
5000
200
The AD7792/AD7793 can be operated in unbuffered mode only
when the gain equals 1 or 2. At higher gains, the buffer is auto-
matically enabled. The absolute input voltage range in buffered
mode is restricted to a range between GND + 100 mV and
AVDD – 100 mV. When the gain is set to 4 or higher, the in-amp
is enabled. The absolute input voltage range when the in-amp is
active is restricted to a range between GND + 300 mV and
AVDD 1.1 V. Take care in setting up the common-mode
voltage so that these limits are not exceeded to avoid
degradation in linearity and noise performance.
The absolute input voltage in unbuffered mode includes the
range between GND – 30 mV and AVDD + 30 mV as a result of
being unbuffered. The negative absolute input voltage limit does
allow the possibility of monitoring small true bipolar signals
with respect to GND.
INSTRUMENTATION AMPLIFIER
Amplifying the analog input signal by a gain of 1 or 2 is
performed digitally within the AD7792/AD7793. However,
when the gain equals 4 or higher, the output from the buffer is
applied to the input of the on-chip instrumentation amplifier.
This low noise in-amp means that signals of small amplitude
can be gained within the AD7792/AD7793 while still
maintaining excellent noise performance.
For example, when the gain is set to 64, the rms noise is 40 nV
typically, which is equivalent to 21 bits effective resolution or
18.5 bits peak-to-peak resolution.
The AD7792/AD7793 can be programmed to have a gain of 1,
2, 4, 8, 16, 32, 64, and 128 using Bit G2 to Bit G0 in the configu-
ration register. Therefore, with an external 2.5 V reference, the
unipolar ranges are from 0 mV to 20 mV to 0 V to 2.5 V while
the bipolar ranges are from ±20 mV to ±2.5 V. When the
in-amp is active (gain ≥ 4), the common-mode voltage (AIN(+)
+ AIN(–))/2 must be greater than or equal to 0.5 V.
If the AD7792/AD7793 are operated with an external reference
that has a value equal to AVDD, the analog input signal must be
limited to 90% of VREF/gain when the in-amp is active, for
correct operation.
BIPOLAR/UNIPOLAR CONFIGURATION
The analog input to the AD7792/AD7793 can accept either
unipolar or bipolar input voltage ranges. A bipolar input range
does not imply that the part can tolerate negative voltages with
respect to system GND. Unipolar and bipolar signals on the
AIN(+) input are referenced to the voltage on the AIN(–) input.
For example, if AIN() is 2.5 V, and the ADC is configured for
unipolar mode and a gain of 1, the input voltage range on the
AIN(+) pin is 2.5 V to 5 V.
If the ADC is configured for bipolar mode, the analog input
range on the AIN(+) input is 0 V to 5 V. The bipolar/unipolar
option is chosen by programming the U/B bit in the configura-
tion register.
DATA OUTPUT CODING
When the ADC is configured for unipolar operation, the output
code is natural (straight) binary with a zero differential input
voltage resulting in a code of 00...00, a midscale voltage
resulting in a code of 100...000, and a full-scale input voltage
resulting in a code of 111...111. The output code for any analog
input voltage can be represented as
Code = (2N × AIN × GAIN)/VREF
When the ADC is configured for bipolar operation, the output
code is offset binary with a negative full-scale voltage resulting
in a code of 000...000, a zero differential input voltage resulting
in a code of 100...000, and a positive full-scale input voltage
resulting in a code of 111...111. The output code for any analog
input voltage can be represented as
Code = 2N – 1 × [(AIN × GAIN /VREF) + 1]
where AIN is the analog input voltage, GAIN is the in-amp
setting (1 to 128), and N = 16 for the AD7792 and N = 24 for
the AD7793.
相關PDF資料
PDF描述
RCM15DCBD-S189 CONN EDGECARD 30POS R/A .156 SLD
0982660775 CBL 9POS 0.5MM JMPR TYPE A 5"
EVAL-AD7734EBZ BOARD EVALUATION FOR AD7734
SK471M100ST CAP ALUM 470UF 100V 20% RADIAL
0982660774 CBL 9POS 0.5MM JMPR TYPE D 5"
相關代理商/技術參數
參數描述
EVAL-AD7793EBZ 制造商:Analog Devices 功能描述:EVAL BOARD, AD7793 3CH 24BIT ADC
EVAL-AD7793EBZ1 制造商:AD 制造商全稱:Analog Devices 功能描述:3-Channel, Low Noise, Low Power, 16-/24-Bit ?￡-?? ADC with On-Chip In-Amp and Reference
EVAL-AD7794EB 制造商:Analog Devices 功能描述:EVALUATION BOARD I.C. - Bulk
EVAL-AD7794EBZ 功能描述:BOARD EVALUATION FOR AD7794 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7795 制造商:AD 制造商全稱:Analog Devices 功能描述:Evaluation Board for the AD7795 16-Bit, Low Power Sigma-Delta ADC (6 Channels)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*