參數資料
型號： EVAL-AD7993EBZ
廠商： Analog Devices Inc
文件頁數： 11/32頁
文件大小： 0K
描述： BOARD EVAL FOR AD7993
標準包裝： 1
ADC 的數量： 1
位數： 10
采樣率（每秒）： 188k
數據接口： 串行
輸入范圍： 0 ~ 5.5 V
在以下條件下的電源（標準）： 7.7mW @ 188kSPS，5.5 V
工作溫度： -40°C ~ 125°C
已用 IC / 零件： AD7993
已供物品： 板，纜線，CD
AD7993/AD7994
Rev. 0 | Page 19 of 32
CONFIGURATION REGISTER
The configuration register is an 8-bit read/write register that is used to set the operating modes of the AD7993/AD7994. The bit functions
are outlined in Table 9. A single-byte write is necessary when writing to the configuration register.
Table 9. Configuration Register Bit Function Descriptions and Default Settings at Power-Up
D7
D6
D5
D4
D3
D2
D1
D0
CH4
CH3
CH2
CH1
FLTR
ALERT EN
BUSY/ALERT
ALERT/BUSY POLARITY
0
1
0
Table 10. Bit Function Descriptions
Bit
Mnemonic
Comment
D7 to D4
CH4 to CH1
These 4-channel address bits select the analog input channel(s) to be converted. A 1 in any of Bits D7 to D4
selects a channel for conversion. If more than one channel bit is set to 1, the AD7993/AD7994 sequence
through the selected channels, starting with the lowest channel. All unused channels should be set to 0.
Table 11 shows how these 4-channel address bits are decoded. Prior to initiating a conversion, the channel(s)
must be selected in the configuration register.
D3
FLTR
The value written to this bit of the control register determines whether the filtering on SDA and SCL is
enabled or is to be bypassed. If this bit is a 1, then the filtering is enabled; if it is a 0, the filtering is bypassed.
D2
ALERT EN
The hardware ALERT function is enabled if this bit is set to 1 and disabled if this bit is set to 0. This bit is used
in conjunction with the BUSY/ALERT bit to determine if the ALERT/BUSY pin act as an ALERT or a BUSY output
D1
BUSY/ALERT
This bit is used in conjunction with the ALERT EN bit to determine if the ALERT/BUSY output, Pin 13, acts as an
ALERT or BUSY output (see Table 12), and if Pin 13 is configured as an ALERT output pin, if it is to be reset.
D0
BUSY/ALERT
POLARITY
This bit determines the active polarity of the ALERT/BUSY pin regardless of whether it is configured as an
ALERT or BUSY output. It is active low if this bit is set to 0, and active high if it is set to 1.
Table 11. Channel Selection
D7
D6
D5
D4
Analog Input Channel
Comments
0
No channel selected; see address pointer byte, Mode 2.
0
1
Convert on VIN1.
0
1
0
Convert on VIN2.
0
1
Sequence between VIN1 and VIN2.
0
1
0
Convert on VIN3.
0
1
0
1
Sequence between VIN1 and VIN3.
0
1
0
Sequence between VIN2 and VIN3.
0
1
Sequence between VIN1, VIN2, and VIN3.
1
0
Convert on VIN4.
1
0
1
Sequence between VIN1 and VIN4.
1
0
1
0
Sequence between VIN2 and VIN4.
1
0
1
Sequence between VIN1, VIN2, and VIN4.
1
0
Sequence between VIN3 and VIN4.
1
0
1
Sequence between VIN1, VIN3, and VIN4.
1
0
Sequence between VIN2, VIN3, and VIN4.
1
Sequence between VIN1, VIN2, VIN3, and VIN4.
The AD7993/AD7994 convert on the selected channel in
the sequence in ascending order, starting with the
lowest channel in the sequence.
Table 12. Alert/Busy Function
D2
D1
ALERT/BUSY Pin Configuration
0
Pin does not provide any interrupt signal.
0
1
Pin configured as a busy output.
1
0
Pin configured as an alert output.
1
Resets the ALERT output pin, the Alert_Flag bit in the conversion result register, and the entire alert status register
(if any is active). If 1/1 is written to Bits D2/D1 in the configuration register to reset the ALERT pin, the Alert_Flag bit,
and the alert status register, the contents of the configuration register read 1/0 for D2/D1, respectively, if read back.
相關PDF資料
PDF描述
EBC17DRTI-S734 CONN EDGECARD 34POS DIP .100 SLD
EVAL-AD7400EDZ BOARD EVAL AD7400
VI-21N-EY CONVERTER MOD DC/DC 18.5V 50W
EVAL-AD7400AEDZ BOARD EVAL AD7400A
EBC20DREN-S734 CONN EDGECARD 40POS .100 EYELET
相關代理商/技術參數
參數描述
EVAL-AD7994CB 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD. - Bulk
EVAL-AD7994CBZ 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD. - Bulk
EVAL-AD7994EBZ 功能描述:BOARD EVAL FOR AD7994 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7995EBZ 功能描述:BOARD EVAL FOR AD7995 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件
EVAL-AD7997CBZ 制造商:Analog Devices 功能描述:EVALUATION CONTROL BOARD (ROHS) - Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*