- 您現在的位置：買賣IC網 > PDF目錄375724 > FAN5231QSC (FAIRCHILD SEMICONDUCTOR CORP) Analog IC PDF資料下載
參數資料
| 型號： | FAN5231QSC |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | Analog IC |
| 中文描述： | 0.34 A SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封裝： | PLASTIC, QSOP-28 |
| 文件頁數： | 11/17頁 |
| 文件大?。?/td> | 360K |
| 代理商： | FAN5231QSC |
FAN5231
REV. 1.1.1 8/15/01
11
The converter output voltage is applied to the negative input
of the hysteretic comparator. The voltage on the reference
input of the hysteretic comparator is the DAC output voltage
with a small addition of the clock frequency pulses. Syn-
chronization of the upper MOSFET turn-on pulses with the
main clock positively contributes to the seamless transition
between the operation modes.
Operation During Processor Mode Changes
The PWM1 controller is specially designed to provide “on
the fly” automatic core voltage changes required by some
advanced processors for mobile applications. Dual core volt-
age and operation frequency scaling allows for significant
power savings without sacrificing system performance in
battery operation mode.
As processor mode changes can happen when chip is in
PWM or hysteretic mode, measures were taken to provide
equally fast response to these changes. As soon as a DAC
code change is received, the chip is switched into the forced
PWM mode for about 150ms regardless of the load level.
Operating the controller in the synhronous PWM mode
allows faster output voltage transitions especially when a
downward output voltage change is commanded.
I/O Converter Architecture
The I/O converter architecture is close to the one of the core
converter. It has the same mode control logic and can operate
in a costant frequency PWM mode or in the hysteretic mode
depending on the load level, but its structure is much simpler
mainly because of absense of the differential input amlifier
and the DAC. This controller is synchronized to the same
clock as the core converter, but out-of phase. Those, some
reduction of the input current ripple is achieved.
Gate Control Logic
The gate control logic translates generated PWM signals
into the MOSFETs gate drive signals providing necessary
amplification, level shift and shoot-trough protection. Also,
it incorporates functions that help to optimize the IC
performance over a wide range of operating conditions.
As MOSFET switching time can very dramatically from
type to type and with input voltage variation, gate control
logic provides adaptive dead time by monitoring gate volt-
ages of both upper and lower MOSFETs.
Output Voltage Adjustment
The output voltage of the I/O converter can be increased by
as much as 10% by inserting a resistor divider in the feed-
back line.
Fault Protection
All three outputs are monitored and protected against
extreme overload, short circuit and under-voltage conditions.
Both PWM outputs are monitored and protected from over-
voltage conditions. Only monitoring functions for over-volt-
age conditions is incorporated for the linear regulator.
A sustained overload on any output latches-off all the con-
verters and sets the PGOOD pin low. The chip operation can
be restored by cycling VCC voltage or EN pin.
Figure 10. I/O Converter Load Transient in PWM Mode
Figure 11. I/O Converter Load Transient
with Mode Change
Over-Current Protection
Both PWM controllers use the lower MOSFET’s on-resis-
tance — r
DS(ON)
to monitor the current for protection against
shorted outputs. The sensed voltage drop after amplification
is compared with an internally set threshold. Several scenar-
ios of the current protection circuit behavior are possible.
If load step is strong enough to pull output voltage lower
than the under-voltage threshold, chip shuts down. If the out-
put voltage sag does not reach the under-voltage threshold
but the current exceeds the over-current threshold, the pulse
skipping circuit is activated. This breaks the output voltage
regulation and limits the current supplied to the load.
Because of the nature of used current sensing technique, and
to accommodate wide range of the r
DS(ON)
variation, the
value of the threshold should represent overload current
about 180% of the nominal value. This could lead to the situ-
ation where the converter continuously delivers power about
two times the nominal without significant drop in the output
Ch1 50mV
Ch2 500mA
M50μs
1
2
V
IO
I
IO
Ch1 50mV
Ch2 500mA
M50μs
1
2
V
IO
I
IO
相關PDF資料 |
PDF描述 |
|---|---|
| FAN5232 | Adjustable PWM Buck Controller for LCD PCs |
| FAN5232MTC | SMPS Controller |
| FAN5233 | System Electronics Regulator for Mobile PCs |
| FAN5233MTC | Analog IC |
| FAN5233MTCX | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN5231QSCX | 功能描述:開關變換器、穩壓器與控制器 QSOP-28 RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
| FAN5232 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Adjustable PWM Buck Controller for LCD PCs |
| FAN5232_CBC3116B WAF | 制造商:Fairchild Semiconductor Corporation 功能描述: |
| FAN5232MTC | 功能描述:DC/DC 開關控制器 DC/DC RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| FAN5232MTC_NL | 功能描述:開關變換器、穩壓器與控制器 ANG FG RoHS:否 制造商:Texas Instruments 輸出電壓:1.2 V to 10 V 輸出電流:300 mA 輸出功率: 輸入電壓:3 V to 17 V 開關頻率:1 MHz 工作溫度范圍: 安裝風格:SMD/SMT 封裝 / 箱體:WSON-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。