參數資料
型號： FAN53180MTC
廠商： FAIRCHILD SEMICONDUCTOR CORP
元件分類： 穩壓器
英文描述： 6-Bit VID Controlled 2-4 Phase DC-DC Controller
中文描述： SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28
封裝： TSSOP-28
文件頁數： 14/28頁
文件大?。?/td> 851K
代理商： FAN53180MTC
FAN53180
PRODUCT SPECIFICATION
14
REV. 1.0.0 6/10/03
To provide the best accuracy for the sensing of current, the
CSA has been designed to have a low offset input voltage.
Also, the sensing gain is determined by external resistors so
that it can be made extremely accurate.
Active Impedance Control Mode
For controlling the dynamic output voltage droop as a
function of output current, a signal proportional to the total
output current at the CSCOMP pin can be scaled to be equal
to the droop impedance of the regulator times the output
current. This droop voltage is then used to set the input
control voltage to the system. The droop voltage is sub-
tracted from the DAC reference input voltage directly to tell
the error amplifier where the output voltage should be. This
differs from previous implementations and allows enhanced
feed-forward response.
Current Control Mode and Thermal Balance
The FAN53180 has individual inputs for each phase which
are used for monitoring the current in each phase. This infor-
mation is combined with an internal ramp to create a current
balancing feedback system that has been optimized for initial
current balance accuracy and dynamic thermal balancing
during operation. This current balance information is inde-
pendent of the average output current information used for
positioning described previously.
The magnitude of the internal ramp can be set to optimize
the transient response of the system. It is also monitors the
supply voltage for feed-forward control for changes in the
supply. A resistor connected from the power input voltage to
the RAMPADJ pin determines the slope of the internal
PWM ramp. Detailed information about programming the
ramp is given in the applications section.
External resistors can be placed in series with individual
phases to create an intentional current imbalance if desired,
such as when one phase may have better cooling and can
support higher currents. Resistors R
SW1
through R
SW4
(see
the typical application circuit in Figure 1) can be used for
adjusting thermal balance. It is best to have the ability to add
these resistors during the initial design, so make sure place-
holders are provided in the layout.
To increase the current in any given phase, make R
SW
for
that phase larger (make R
SW
= 0 for the hottest phase and do
not change during balancing). Increasing R
SW
to only 500
will make a substantial increase in phase current. Increase
each R
SW
value by small amounts to achieve balance, start-
ing with the coolest phase first.
Voltage Control Mode
A high gain-bandwidth voltage mode error amplifier is used
for the voltage-mode control loop. The control input voltage
to the positive input is set via the VID 6-bit logic code
according to the voltages listed in Table 1. This voltage is
also offset by the droop voltage for active positioning of the
output voltage as a function of current, commonly known as
active voltage positioning. The output of the amplifier is the
COMP pin, which sets the termination voltage for the inter-
nal PWM ramps.
The negative input (FB) is tied to the output sense location
with a resistor R
B
and is used for sensing and controlling the
output voltage at this point. A current source from the FB pin
flowing through R
B
is used for setting the no-load offset
voltage from the VID voltage. The no-load voltage will be
negative with respect to the VID DAC. The main loop com-
pensation is incorporated in the feedback network between
FB and COMP.
Soft-Start
The power-on ramp up time of the output voltage is set with
a capacitor and resistor in parallel from the DELAY pin to
ground. The RC time constant also determines the current
limit latch off time as explained in the following section. In
UVLO or when EN is a logic low, the DELAY pin is held at
ground. After the UVLO threshold is reached and EN is a
logic high, the DELAY cap is charged up with an internal
20μA current source. The output voltage follows the ramping
voltage on the DELAY pin, limiting the inrush current. The
soft-start time depends on the value of VID DAC and C
DLY
,
with a secondary effect from R
DLY
. Refer to the applications
section for detailed information on setting C
DLY
.
When the PWRGD threshold is reached, the soft-start cycle
is stopped and the DELAY pin is pulled up to 3V. This
ensures that the output voltage is at the VID voltage when
the PWRGD signals to the system that the output voltage is
good. If EN is taken low or VCC drops below UVLO, the
DELAY cap is reset to ground to be ready for another soft
start cycle. Figure 2 shows a typical start-up sequence for
the FAN53180.
Current Limit, Short Circuit and Latch-off
Protection
The FAN53180 compares a programmable current limit set
point to the voltage from the output of the current senseam-
plifier. The level of current limit is set with the resistor from
the ILIMIT pin to ground. During normal operation, the volt-
age on ILIMIT is 3V. The current through the external resis-
tor is internally scaled to give a current limit threshold of
10.4mV/μA. If the difference in voltage between CSREF and
CSCOMP rises above the current limit threshold, the internal
current limit amplifier will control the internal COMP volt-
age to maintain the average output current at the limit.
相關PDF資料
PDF描述
FAN53180 6-Bit VID Controlled 2-4 Phase DC-DC Controller
FAN5330 High Efficiency Serial LED Driver with 30V Integrated Switch
FAN5331 1.6MHz Boost Converter with 20V Integrated FET Switch
FAN5331SX 1.6MHz Boost Converter with 20V Integrated FET Switch
FAN5332A High Efficiency, High Current Serial LED Driver and OLED Supply with 30V Integrated Switch
相關代理商/技術參數
參數描述
FAN53180MTCX 功能描述:DC/DC 開關控制器 Buck Controller 2to4 Phs VID Sync RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK
FAN5330 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:High Efficiency Serial LED Driver with 30V Integrated Switch
FAN5330SX 功能描述:LED照明驅動器 SYSTEM_POWER RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N
FAN5331 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
FAN5331_05 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:High Efficiency Serial LED Driver and OLED Supply with 20V Integrated Switch
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*