參數資料
型號: FLEX10KA
廠商: Altera Corporation
英文描述: Embedded Programmable Logic Family
中文描述: 嵌入式可編程邏輯系列
文件頁數: 34/114頁
文件大?。?/td> 1422K
代理商: FLEX10KA
34
Altera Corporation
FLEX 10K Embedded Programmable Logic Family Data Sheet
ClockLock &
ClockBoost
Features
To support high-speed designs, selected FLEX 10K devices offer optional
ClockLock and ClockBoost circuitry containing a phase-locked loop (PLL)
that is used to increase design speed and reduce resource usage. The
ClockLock circuitry uses a synchronizing PLL that reduces the clock delay
and skew within a device. This reduction minimizes clock-to-output and
setup times while maintaining zero hold times. The ClockBoost circuitry,
which provides a clock multiplier, allows the designer to enhance device
area efficiency by resource sharing within the device. ClockBoost allows
the designer to distribute a low-speed clock and multiply that clock on-
device. Combined, the ClockLock and ClockBoost features provide
significant improvements in system performance and bandwidth.
The ClockLock and ClockBoost features in FLEX 10K devices are enabled
through the MAX+PLUS II software. External devices are not required to
use these features. The output of the ClockLock and ClockBoost circuits is
not available at any of the device pins.
The ClockLock and ClockBoost circuitry locks onto the rising edge of the
incoming clock. The circuit output can only drive the clock inputs of
registers; the generated clock cannot be gated or inverted.
The dedicated clock pin (
GCLK1
) supplies the clock to the ClockLock and
ClockBoost circuitry. When the dedicated clock pin is driving the
ClockLock or ClockBoost circuitry, it cannot drive elsewhere in the
device.
In designs that require both a multiplied and non-multiplied clock, the
clock trace on the board can be connected to
GCLK1
. With the
MAX+PLUS II software,
GCLK1
can feed both the ClockLock and
ClockBoost circuitry in the FLEX 10K device. However, when both
circuits are used, the other clock pin (
GCLK0
) cannot be used. Figure 16
shows a block diagram of how to enable both the ClockLock and
ClockBoost circuits in the MAX+PLUS II software. The example shown is
a schematic, but a similar approach applies for designs created in AHDL,
VHDL, and Verilog HDL. When the ClockLock and ClockBoost circuits
are used simultaneously, the input frequency parameter must be the same
for both circuits. In Figure 16, the input frequency must meet the
requirements specified when the ClockBoost multiplication factor is two.
相關PDF資料
PDF描述
FLEX10KE Embedded Programmable Logic Family
FLEX6000 Programmable Logic Device Family
FLEX8000 PROGRAMMABLE LOGIC DEVICES FAMILY
FLL120MK L-Band Medium & High Power GaAs FET
FLL200IB-1 L-Band Medium & High Power GaAs FET
相關代理商/技術參數
參數描述
FLEX10KE 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:Embedded Programmable Logic Device
FLEX110 功能描述:開發板和工具包 - PIC / DSPIC Multibus Pack RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓:
FLEX111 功能描述:開發板和工具包 - PIC / DSPIC Fasttrack suite RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓:
FLEX112 功能描述:開發板和工具包 - PIC / DSPIC Demo2 Pack RoHS:否 制造商:Microchip Technology 產品:Starter Kits 工具用于評估:chipKIT 核心:Uno32 接口類型: 工作電源電壓:
FLEX113 功能描述:開發板和工具包 - 無線 Mini Kit RoHS:否 制造商:Arduino 產品:Evaluation Boards 工具用于評估:AT32UC3L 核心:AVR32 頻率: 接口類型:USB 工作電源電壓:5 V