參數資料
型號： FT2232H MINI MODULE
廠商： FTDI, Future Technology Devices International Ltd
文件頁數： 5/67頁
文件大?。?/td> 0K
描述： MOD USB HS FT2232H EVAL
產品變化通告： Part Number Change Jan 2011
產品目錄繪圖： FT(22, 42)32HQ MINI MOD
標準包裝： 5
主要目的： 接口，USB 2.0 至 UART、JTAG、SPI、I2C
嵌入式： 否
已用 IC / 零件： FT2232H
主要屬性： 高速，異步串行數據，300 波特 ~ 12 Mbaud，TTL 級
次要屬性： JTAG、SPI 和 I2C 上同步串行（MPSSE）數據傳輸速度高達 30Mbps
已供物品： 板
產品目錄頁面： 633 (CN2011-ZH PDF)
相關產品： 768-1010-6-ND - IC USB FS DUAL UART/FIFO 48-LQFP
768-1010-1-ND - IC USB FS DUAL UART/FIFO 48-LQFP
768-1010-2-ND - IC USB FS DUAL UART/FIFO 48-LQFP
其它名稱： 768-1030
FT2232HQ_MINI MOD
Copyright 2012 Future Technology Devices International Limited
13
Document No.: FT_000061
FT2232H DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
Version 2.21
Clearance No.: FTDI#77
3.4.2 FT2232H pins used in an FT245 Style Synchronous FIFO Interface
The FT2232H only channel A can be configured as a FT245 style synchronous FIFO interface. When
configured in this mode, the pins used and the descriptions of the signals are shown in Table 3.5. To
enter this mode the external EEPROM must be set to make port A 245 mode. A software command (Set
Bit Mode option) is then sent by the application to the FTDI driver to tell the chip to enter single channel
synchronous FIFO mode. In this mode the B channel is not available as all resources have been switched
onto channel A. In this mode, data is written or read on the rising edge of the CLKOUT.
Channel A
Pin No.
Name
Type
FT245 Configuration Description
24,23,22,21,
19,18,17,16
ADBUS[7:0]
I/O
D7 to D0 bidirectional FIFO data. This bus is normally input unless
OE# is low.
26
RXF#
OUTPUT
When high, do not read data from the FIFO. When low, there is data
available in the FIFO which can be read by driving RD# low. When in
synchronous mode, data is transferred on every clock that RXF# and
RD# are both low. Note that the OE# pin must be driven low at least
1 clock period before asserting RD# low.
27
TXE#
OUTPUT
When high, do not write data into the FIFO. When low, data can be
written into the FIFO by driving WR# low. When in synchronous
mode, data is transferred on every clock that TXE# and WR# are both
low.
28
RD#
INPUT
Enables the current FIFO data byte to be driven onto D0...D7 when
RD# goes low. The next FIFO data byte (if available) is fetched from
the receive FIFO buffer each CLKOUT cycle until RD# goes high.
29
WR#
INPUT
Enables the data byte on the D0...D7 pins to be written into the
transmit FIFO buffer when WR# is low. The next FIFO data byte is
written to the transmit FIFO buffer each CLKOUT cycle until WR# goes
high.
32
CLKOUT
OUTPUT
60 MHz Clock driven from the chip. All signals should be synchronized
to this clock.
33
OE#
INPUT
Output enable when low to drive data onto D0-7. This should be
driven low at least 1 clock period before driving RD# low to allow for
data buffer turn-around.
30
SIWU
INPUT
The Send Immediate / WakeUp signal combines two functions on a
single pin. If USB is in suspend mode (PWREN# = 1) and remote
wakeup is enabled in the EEPROM , strobing this pin low will cause the
device to request a resume on the USB Bus. Normally, this can be
used to wake up the Host PC.
During normal operation (PWREN# = 0), if this pin is strobed low any
data in the device TX buffer will be sent out over USB on the next
Bulk-IN request from the drivers regardless of the pending packet
size. This can be used to optimize USB transfer speed for some
applications. Tie this pin to VCCIO if not used. (Also see note 1, 2, 3
in section 4.12)
Table 3.5 Channel A FT245 Style Synchronous FIFO Configured Pin Descriptions
For a functional description of this mode, please refer to section 4.4
相關PDF資料
PDF描述
RNF-100-1/4-OR-SP HEAT SHRINK TUBING
GBM25DTAN-S189 CONN EDGECARD 50POS R/A .156 SLD
RNF-100-1/4-OR-STK HEAT SHRINK TUBING
RNF-100-1/4-BN-SP HEAT SHRINK TUBING
0210391007 CABLE JUMPER 1MM .305M 29POS
相關代理商/技術參數
參數描述
FT2232HQ 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB Hi-Speed to Dual Channel Serial UART/FIFO/JTAG/SPI/I2C IC - QFN-64
FT2232HQ_MINI_ MODULE 功能描述:界面開發工具 USB Hi-Speed FT2232H Evaluation Module RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
FT2232HQ-4000 制造商:FTDI 制造商全稱:FTDI 功能描述:DUAL HIGH SPEED USB TO MULTIPURPOSE UART/FIFO IC
FT2232HQ-MINI-MODULE 制造商:Future Technology Devices International (FTDI Chip) 功能描述:MODULE USB 2 PORT FT2232H BASED 制造商:Future Technology Devices International (FTDI Chip) 功能描述:MOD, USB TO SERIAL / FIFO, FT2232H 制造商:Future Technology Devices International (FTDI Chip) 功能描述:MOD, CONV, USB TO SERIAL / FIFO, 2 PORT, FT2232H; ;ROHS COMPLIANT: YES
FT2232HQ-R 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB-UART/FIFO 2232 DUAL 64QFN 制造商:Future Technology Devices International (FTDI Chip) 功能描述:USB-UART/FIFO, 2232, DUAL, 64QFN 制造商:Future Technology Devices International (FTDI Chip) 功能描述:IC, DUAL UART, FIFO 480MBPS 3.63V QFN-64; No. of Channels:2; Data Rate:480Mbps; Supply Voltage Min:2.97V; Supply Voltage Max:3.63V; Digital IC Case Style:QFN; No. of Pins:64; Operating Temperature Min:-40C; Voltage, Vcc:1.8V ;RoHS Compliant: Yes
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*