參數資料
型號: FW300H1
廠商: LINEAGE POWER LLC
元件分類: 電源模塊
英文描述: DC-DC REG PWR SUPPLY MODULE
文件頁數: 4/20頁
文件大?。?/td> 839K
代理商: FW300H1
12
Lineage Power
Data Sheet
April 2008
36 Vdc to 75 Vdc Input, 24 Vdc Output; 250 W to 300 W
FW250H1 and FW300H1 Power Modules; dc-dc Converters:
Feature Descriptions (continued)
Output Current Monitor
The CURRENT MON pin provides a dc voltage propor-
tional to the dc output current of the module given in
the Feature Specifications table. For example, on the
FW250H1, the V/A ratio is set at 250 mV/A
± 10% @
70
°C case. At a full load current of 12.5 A, the voltage
on the CURRENT MON pin is 3.13 V. The current mon-
itor signal is referenced to the SENSE(–) pin on the
secondary and is supplied from a source impedance of
approximately 2 k
Ω. It is recommended that the CUR-
RENT MON pin be left open when not in use, although
no damage will result if the CURRENT MON pin is
shorted to secondary ground. Directly driving the CUR-
RENT MON pin with an external source will detrimen-
tally affect operation of the module and should be
avoided.
Synchronization
Any module can be synchronized to any other module
or to an external clock using the SYNC IN or SYNC
OUT pins. The modules are not designed to operate in
a master/slave configuration; that is, if one module
fails, the other modules will continue to operate.
SYNC IN Pin
This pin can be connected either to an external clock or
directly to the SYNC OUT pin of another FW250x or
FW300x module.
If an external clock signal is applied to the SYNC IN
pin, the signal must be a 500 kHz (±50 kHz) square
wave with a 4 Vp-p amplitude. Operation outside this
frequency band will detrimentally affect the perfor-
mance of the module and must be avoided.
If the SYNC IN pin is connected to the SYNC OUT pin
of another module, the connection should be as direct
as possible, and the VI(–) pins of the modules must be
shorted together.
Unused SYNC IN pins should be tied to VI(–). If the
SYNC IN pin is unused, the module will operate from
its own internal clock.
SYNC OUT Pin
This pin contains a clock signal referenced to the VI(–)
pin. The frequency of this signal will equal either the
module’s internal clock frequency or the frequency estab-
lished by an external clock applied to the SYNC IN pin.
When synchronizing several modules together, the
modules can be connected in a daisy-chain fashion
where the SYNC OUT pin of one module is connected
to the SYNC IN pin of another module. Each module in
the chain will synchronize to the frequency of the first
module in the chain.
To avoid loading effects, ensure that the SYNC OUT
pin of any one module is connected to the SYNC IN pin
of only one module. Any number of modules can be
synchronized in this daisy-chain fashion.
Overtemperature Protection
To provide protection in a fault condition, the unit is
equipped with an overtemperature shutdown circuit.
The shutdown circuit will not engage unless the unit is
operated above the maximum case temperature.
Recovery from overtemperature shutdown is
accomplished by cycling the dc input power off for at
least 1.0 second or toggling the primary referenced on/
off signal for at least 1.0 second.
Forced Load Sharing (Parallel Operation)
For either redundant operation or additional power
requirements, the power modules can be configured for
parallel operation with forced load sharing (see
Figure 19). For a typical redundant configuration,
Schottky diodes or an equivalent should be used to
protect against short-circuit conditions. Because of the
remote sense, the forward-voltage drops across the
Schottky diodes do not affect the set point of the
voltage applied to the load. For additional power
requirements, where multiple units are used to develop
combined power in excess of the rated maximum, the
Schottky diodes are not needed.
Good layout techniques should be observed for noise
immunity. To implement forced load sharing, the follow-
ing connections must be made:
相關PDF資料
PDF描述
FW250H1 DC-DC REG PWR SUPPLY MODULE
FW300R1 1-OUTPUT 305.485 W DC-DC REG PWR SUPPLY MODULE
FW250R1 1-OUTPUT 256.95 W DC-DC REG PWR SUPPLY MODULE
FW330D1 1-OUTPUT 200 W DC-DC REG PWR SUPPLY MODULE
FW330F1 1-OUTPUT 330 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
FW300-P 制造商:Maxell 功能描述:Ear Bud Headphone With Microphone - With Apple Control - Pink
FW300R1 功能描述:CONVERTER DC/DC 28V 300W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:FW300 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入(最小):42V 電壓 - 輸入(最大):60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出(最大):* 電源(瓦) - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H(116.8mm x 45.7mm x 13.2mm) 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源(瓦特)- 最大:*
FW300S6R0 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC-to-DC Voltage Converter
FW3012-760 功能描述:插入式交流適配器 30 Watts 12V RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓(通道 1):5 V 輸出電流(通道 1):1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V
FW3012-760F 功能描述:插入式交流適配器 30 Watt 12V RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓(通道 1):5 V 輸出電流(通道 1):1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V