參數資料
型號: FW300H1
廠商: LINEAGE POWER LLC
元件分類: 電源模塊
英文描述: DC-DC REG PWR SUPPLY MODULE
文件頁數: 5/20頁
文件大?。?/td> 839K
代理商: FW300H1
Lineage Power
13
Data Sheet
April 2008
36 Vdc to 75 Vdc Input, 24 Vdc Output; 250 W to 300 W
FW250H1 and FW300H1 Power Modules; dc-dc Converters:
Feature Descriptions (continued)
Forced Load Sharing (Parallel Operation)
(continued)
n
The parallel pins of all units must be connected
together. The paths of these connections should be
as direct as possible.
n
All remote-sense pins should be connected to the
power bus at the same point, i.e., connect all
SENSE(+) pins to the (+) side of the power bus at the
same point and all SENSE(–) pins to the (–) side of
the power bus at the same point. Close proximity and
directness are necessary for good noise immunity.
When not using the parallel feature, leave the
PARALLEL pin open.
8-581
Figure 19. Wiring Configuration for Redundant
Parallel Operation
Power Good Signal
The PWR GOOD pin provides an open-drain signal
(referenced to the SENSE(–) pin) that indicates the
operating state of the module. A low impedance
(<100
Ω) between PWR GOOD and SENSE(–) indi-
cates that the module is operating. A high impedance
(>1 M
Ω) between PWR GOOD and SENSE(–) indi-
cates that the module is off or has failed. The PWR
GOOD pin can be pulled up through a resistor to an
external voltage to facilitate sensing. This external volt-
age level must not exceed 40 V, and the current into
the PWR GOOD pin during the low-impedance state
should be limited to 1 mA maximum.
Thermal Considerations
Introduction
The power modules operate in a variety of thermal
environments; however, sufficient cooling should be
provided to help ensure reliable operation of the unit.
Heat-dissipating components inside the unit are ther-
mally coupled to the case. Heat is removed by conduc-
tion, convection, and radiation to the surrounding
environment. Proper cooling can be verified by mea-
suring the case temperature. Peak temperature occurs
at the position indicated in Figure 20.
8-1303
Note: Top view, measurements shown in millimeters and (inches).
Pin locations are for reference only.
Figure 20. Case Temperature Measurement
Location
VO(+)
PARALLEL
SENSE(+)
SENSE(–)
VO(–)
CASE
VI(+)
ON/OFF
VI(–)
VO(+)
PARALLEL
SENSE(+)
SENSE(–)
VO(–)
CASE
VI(+)
ON/OFF
VI(–)
CASE
SYNC IN
SYNC OUT
MEASURE CASE
TEMPERATURE HERE
ON/OFF
82.6
(3.25)
30.5
(1.20)
VI(+)
VI(–)
VO(+)
VO(–)
相關PDF資料
PDF描述
FW250H1 DC-DC REG PWR SUPPLY MODULE
FW300R1 1-OUTPUT 305.485 W DC-DC REG PWR SUPPLY MODULE
FW250R1 1-OUTPUT 256.95 W DC-DC REG PWR SUPPLY MODULE
FW330D1 1-OUTPUT 200 W DC-DC REG PWR SUPPLY MODULE
FW330F1 1-OUTPUT 330 W DC-DC REG PWR SUPPLY MODULE
相關代理商/技術參數
參數描述
FW300-P 制造商:Maxell 功能描述:Ear Bud Headphone With Microphone - With Apple Control - Pink
FW300R1 功能描述:CONVERTER DC/DC 28V 300W OUT RoHS:否 類別:電源 - 板載 >> DC DC Converters 系列:FW300 設計資源:VI-200, VI-J00 Design Guide, Appl Manual 標準包裝:1 系列:* 類型:隔離 輸出數:1 電壓 - 輸入(最小):42V 電壓 - 輸入(最大):60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 電流 - 輸出(最大):* 電源(瓦) - 制造商系列:150W 電壓 - 隔離:* 特點:* 安裝類型:通孔 封裝/外殼:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H(116.8mm x 45.7mm x 13.2mm) 包裝:散裝 工作溫度:-55°C ~ 85°C 效率:* 電源(瓦特)- 最大:*
FW300S6R0 制造商:未知廠家 制造商全稱:未知廠家 功能描述:DC-to-DC Voltage Converter
FW3012-760 功能描述:插入式交流適配器 30 Watts 12V RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓(通道 1):5 V 輸出電流(通道 1):1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V
FW3012-760F 功能描述:插入式交流適配器 30 Watt 12V RoHS:否 制造商:Phihong 地區:Universal 安裝風格:Wall, Interchangeable Plug 輸入電壓范圍:90 VAC to 264 VAC 輸出端數量:1 輸出功率額定值:5 W 輸出電壓(通道 1):5 V 輸出電流(通道 1):1 A 直流輸出連接器:USB Type A 隨附/必需的交流插頭:Required 商用/醫用:Commercial 效率:Level V