- 您現在的位置：買賣IC網 > PDF目錄67593 > FW330S3R671-56 1-OUTPUT 330 W DC-DC REG PWR SUPPLY MODULE PDF資料下載
參數資料
| 型號： | FW330S3R671-56 |
| 元件分類： | 電源模塊 |
| 英文描述： | 1-OUTPUT 330 W DC-DC REG PWR SUPPLY MODULE |
| 封裝： | 2.40 X 4.60 INCH, 0.57 INCH HEIGHT, POWER MODULE |
| 文件頁數： | 8/29頁 |
| 文件大?。?/td> | 347K |
| 代理商： | FW330S3R671-56 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Tyco Electronics Corp.
15
Advance Data Sheet
March 2000
36 to 75 Vdc Input, 3.6, 3.3, 2.5, 2.0, or 1.8 Vdc Output; 180 W to 330 W
FW330 Power Modules: dc-dc Converters;
Feature Descriptions (continued)
Output Voltage Set-Point Adjustment (Trim)
(continued)
8-2820 (F)
Figure 25. Resistor Selection for Increased Output
Voltage
Output Overvoltage Protection
The output overvoltage shutdown consists of control
circuitry, independent of the primary regulation loop,
that monitors the voltage on the output terminals. The
control loop of the over voltage protection has a higher
voltage set point than the primary loop (see Feature
Specications table). This provides a redundant voltage
control that reduces the risk of output overvoltage and
latches the converter off if an overvoltage occurs.
Recovery from latched shutdown is accomplished by
cycling the dc input power off for at least 1.0 second or
by toggling the primary or secondary referenced
remote on/off signal for at least 1.0 second.
The overvoltage shutdown set point can be lowered by
placing a resistor between the overvoltage trim
(OVTRIM) pin and SENSE(–) pin. This feature is useful
if the output voltage of the converter has been trimmed
down and a corresponding reduction in overvoltage trip
point is desired.
The resistance required from a given overvoltage nom-
inal set point is derived from the following equation:
Where:
Rov-adj is the value of an external resistor between the
OVTRIM pin and SENSE(–) pin.
Vov-set is the nominal adjusted set point of the overvolt-
age shutdown threshold.
Output Current Monitor
The CURRENT MON pin provides a dc voltage propor-
tional to the dc output current of the module given in
the Feature Specications table. For example, on the
FW330Y1, the V/A ratio is set at 45 mV/A
± 10% @
70
°C case. At a full load current of 100 A, the voltage
on the CURRENT MON pin is 4.5 V. The current moni-
tor signal is referenced to the SENSE(–) pin on the
secondary and is supplied from a source impedance of
approximately 20 k
. It is recommended that the CUR-
RENT MON pin be left open when not in use, although
no damage will result if the CURRENT MON pin is
shorted to secondary ground. Directly driving the CUR-
RENT MON pin with an external source will detrimen-
tally affect operation of the module and should be
avoided.
Module Synchronization
Any module can be synchronized to any other module
or to an external clock using the SYNC IN or SYNC
OUT pins. The modules are not designed to operate in
a master/slave conguration; that is, if one module fails,
the other modules will continue to operate.
SYNC IN Pin
This pin can be connected either to an external clock or
directly to the SYNC OUT pin of another module.
If an external clock signal is applied to the SYNC IN
pin, the signal must be a 500 kHz (±50 kHz) square
wave with a 4 Vp-p amplitude. Operation outside this
frequency band will detrimentally affect the perfor-
mance of the module and must be avoided.
If the SYNC IN pin is connected to the SYNC OUT pin
of another module, the connection should be as direct
as possible, and the VI(–) pins of the modules must be
shorted together.
Unused SYNC IN pins should be tied to VI(–). If the
SYNC IN pin is not used, the module will operate from
its own internal clock.
1M
0
% CHANGE IN OUTPUT VOLTAGE (
%)
ADJUSTMENT
RESISTOR
VALUE
(
)
1k
2468
10
100k
10k
1.8 V
2.0 V
2.5 V
3.6 V
3.3 V
Rov-adj
4.3
2 Vov-set
–
Vov-set
4.3
–
-------------------------------------
k
=
相關PDF資料 |
PDF描述 |
|---|---|
| FW330F1-33T | 1-OUTPUT 330 W DC-DC REG PWR SUPPLY MODULE |
| FW330Y1-33T | 1-OUTPUT 180 W DC-DC REG PWR SUPPLY MODULE |
| FW400R61-18 | 1-OUTPUT 392 W DC-DC REG PWR SUPPLY MODULE |
| FX2030C | SPECIALTY CONSUMER CIRCUIT, DIP42 |
| FX2030Z | SPECIALTY CONSUMER CIRCUIT, DIP42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FW332 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| FW340 | 制造商:SANYO 制造商全稱:Sanyo Semicon Device 功能描述:N-Channel and P-Channel Silicon MOSFETs General-Purpose Switching Device |
| FW-34-01-F-D-250-100 | 制造商:Samtec Inc 功能描述:.050'' BOARD SPACERS - Bulk |
| FW-34-01-F-D-280-125 | 制造商:Samtec Inc 功能描述:.050'' BOARD SPACERS - Bulk |
| FW-34-01-F-D-350-065 | 制造商:Samtec Inc 功能描述:CONN BD STACKER HDR 68 POS 1.27MM SLDR ST TH - Bulk |
發布緊急采購，3分鐘左右您將得到回復。