GENNUM CORPORATION
522 - 45 - 05
24
G
4h
3-0
ACID[3:0]
Designates the 4 LSBs of the audio control packet DID word. The 6 MSBs are
internally generated.
“
ACID[3]
”
is the MSB and
“
ACID[0]
”
is the LSB.
R/W
Fh
4
RSV
Not used.
-
5
MUTE
Audio mute enable. Same functionality as the MUTE pin. When set HIGH, the
multiplexed audio and extended data packets are forced to zero.
R/W
0
6
AC34/12
Audio control packet channel pair select. When set HIGH, audio control
packet delay data for audio channels 3 and 4 is captured in registers Ah, Bh,
Ch and Dh. When set LOW, audio control packet delay data for audio
channels 1 and 2 is captured in registers #Ah, #Bh, #Ch and #Dh.
R/W
0
7
CASCADE
Cascade select. When set HIGH, the GS9023 device is part of a cascaded
architecture. New packets are multiplexed into the video signal starting at the
first free location of the HANC space if there is sufficient remaining space to
insert the packet. When set LOW, new packets are multiplexed into the video
signal starting after EAV. Existing ancillary data packets are overwritten and
the remaining ancillary space is cleared.
R/W
0
5h
7-0
PKTID[7:0]
Designates the 8 LSBs of the arbitrary data packet DID word. The 2 MSBs
are internally generated.
“
PKTID[7]
”
is the MSB and
“
PKTID[0]
”
is the LSB.
R/W
0
6h
1-0
BUFSEL[1:0]
Video/audio delay mode.
“
BUFSEL[1]
”
is the MSB and
“
BUFSEL[0]
”
is the
LSB. See Table 13
R/W
0
7-2
RSV
Not used.
-
7h
0
ADERR
Audio data packet multiplexing error. The packet will not be multiplexed
because of insufficient room in the HANC space. Error is cleared when read.
R
0
1
ACERR
Audio control packet multiplexing error. The packet will not be multiplexed
because of insufficient room in the HANC space. Error is cleared when read.
R
0
7-2
RSV
Not used.
-
8h
0
RSV
Not used.
-
1
PKTPRTY
Arbitrary data packet parity select. When set HIGH, a parity bit is generated
for every user data word (UDW) of an arbitrary data packet. This overwrites
any data input at the PKT[8] pin.
R/W
0
5-2
RSV
Not used.
-
6
AXST1/2
Audio CH1/2 detection flag. When set HIGH, an audio signal has been
detected.
R
0
7
AXST3/4
Audio CH3/4 detection flag. When set HIGH, an audio signal has been
detected.
R
0
9h
7-0
PKTLINE[7:0]
Arbitrary data packet insertion line. Designates the horizontal line on which
the GS9023 can multiplex arbitrary data packets in the video signal.
R/W
0
Ah
7-0
DELA/B[7:0]
Audio control packet delay. Designates the audio control packet delay data
as specified in the SMPTE 272M standard.
“
DELA
”
corresponds to audio
channels 1 and 2, while
“
DELB
”
corresponds to audio channels 3 and 4.
“
DELA/B[25]
”
is the MSB and
“
DELA/B[0]
”
is the LSB.
R/W
0
Bh
7-0
DELA/B[15:8]
R/W
0
Ch
7-0
DELA/B[23:16]
R/W
0
Dh
1-0
DELA/B[25:24]
R/W
0
2
ACSYNCA/B
Audio control packet synchronization data. Designates the sync mode bits
(asx, asy), as defined in SMPTE 272M (Section 14.5), of channels 1/2 or 3/4
of the audio control packet. The bits are selected by
“
AC34/12
”
in register
#4h.
R/W
0
3
ACDLY
Audio control packet delay active. Designates the
‘
e
’
bit of word
“
DELx0
”
of
an audio control packet as defined in SMPTE 272 (Section 14.7). When set
HIGH indicates valid audio delay data.
R/W
0
7-4
RSV
Not used.
-
TABLE 14: Multiplex Mode Host Interface Registers (Continued)
ADDRESS
BIT
NAME
FUNCTION
R/W
DEFAULT