- 您現在的位置：買賣IC網 > PDF目錄1922 > HA456CM (Intersil)IC VIDEO CROSSPOINT SWIT 44PLCC PDF資料下載
參數資料
| 型號： | HA456CM |
| 廠商： | Intersil |
| 文件頁數： | 7/13頁 |
| 文件大小： | 0K |
| 描述： | IC VIDEO CROSSPOINT SWIT 44PLCC |
| 標準包裝： | 26 |
| 功能： | 視頻交叉點開關 |
| 電路： | 1 x 8:8 |
| 電壓電源： | 雙電源 |
| 電壓 - 電源，單路/雙路(±)： | ±4.5 V ~ 5.5 V |
| 電流 - 電源： | 68mA |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 44-LCC（J 形引線） |
| 供應商設備封裝： | 44-PLCC |
| 包裝： | 管件 |
3
FN4153.7
September 26, 2008
Pin Descriptions
NAME
FUNCTION
NC
No connect. Not internally connected.
D1/SER OUT
Parallel Data Bit input D1 for Parallel Programming Mode. Serial Data Output (MSB of shift register) for cascading multiple
HA456s in serial programming mode. Simply connect Serial Data Out of one HA456 to Serial Data In of another HA456 to daisy
chain multiple devices.
D0/SER IN
Parallel Data Bit Input D0 for Parallel Programming Mode. Serial Data Input (input to shift register) for serial programming mode.
A2, A1, A0
Output Channel Address Bits. These inputs select the output being programmed in parallel programming mode.
IN0-IN7
Analog Video Input Lines.
DGND
Digital Ground. Connect both DGND pins to AGND.
EDGE/LEVEL
A user strapped input that defines whether synchronous channel switching is edge or level controlled. With this pin is strapped
high, the slave register loads from the master register (thus changing the switch matrix state) on the rising edge of the LATCH
signal. If it is strapped low (level mode), the slave register is transparent while LATCH is low, passing data directly from the
master register to the switch state decoders. Strapping EDGE/LEVEL and LATCH low causes the channel switch to execute on
the WR rising edge (not recommended for serial mode operation).
V+
Positive Supply Voltage. Connect all V+ pins together and decouple each pin to AGND (see Figure 2).
SER/PAR
A user strapped input that defines whether the serial (SER/PAR = 1) or parallel (SER/PAR = 0) digital programming interface is
being utilized.
V-
Negative Supply Voltage. Connect both V- pins together and decouple each pin to AGND (see Figure 2).
WR
WRITE Input. In serial mode, data shifts into the shift register (Master Register) LSB from SER IN on the WR rising edge. In
parallel mode, the Master Register loads with D3:0 (if D3:0 = 0000 through 1000), or the appropriate action is taken
(if D3:0 =1011 through 1111), on the WR rising edge (see Table 1).
LATCH
Synchronous Channel Switch Control Input. If EDGE/LEVEL = 1, data is loaded from the Master Register to the Slave Register
on the rising edge of LATCH. If EDGE/LEVEL = 0, data is loaded from the Master to the Slave Register while LATCH = 0. In
parallel mode, commands 1011 through 1110 execute asynchronously, on the WR rising edge, regardless of the state of LATCH
or EDGE/LEVEL. Parallel mode command 1111 executes a software “Latch” (see Table 1).
CE
Chip Enable. When CE = 0 and CE = 1, the WR line is enabled.
CE
Chip Enable. When CE = 0 and CE = 1, the WR line is enabled.
OUT7-OUT0
Analog Video Outputs.
AGND
Analog Ground.
D3
Parallel Data Bit Input D3 when SER/PAR = 0. D3 is unused with serial programming.
D2
Parallel Data Bit Input D2 when SER/PAR = 0. D2 is unused with serial programming.
HA456
相關PDF資料 |
PDF描述 |
|---|---|
| HC5513BIM | IC SLIC DLC/FLC LP STDBY 22-DIP |
| HC55143IM | IC SLIC UNIVERSAL LP 32-PLCC |
| HC5515CMZ | IC SLIC ITU CO/PABX LP 28-PLCC |
| HC9P5504B-5ZX96 | IC SLIC EIA/ITU PABX 24-SOIC |
| HD3-6402R-9Z | IC UART CMOS 5V 2MHZ 40-DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HA456CMZ | 功能描述:模擬和數字交叉點 IC W/ANNEAL XPOINT 8X8 VID GAIN+1 44PLCC RoHS:否 制造商:Micrel 配置:2 x 2 封裝 / 箱體:MLF-16 數據速率:10.7 Gbps 輸入電平:CML, LVDS, LVPECL 輸出電平:CML 電源電壓-最大:3.6 V 電源電壓-最小:2.375 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 產品:Digital Crosspoint 封裝:Tube |
| HA456CN | 制造商:Rochester Electronics LLC 功能描述:XPOINT 8X8 VIDEO GAIN+1 44MQFP COM - Bulk |
| HA456CP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HA456EVAL1 | 功能描述:交換機 IC 開發工具 EVAL PLATFORM HA456 RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:USB Power Switches 工具用于評估:MAX4984E 工作電源電壓:2.8 V to 5.5 V |
| HA457 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:95MHz, Low Power, AV = 2, 8 x 8 Video Crosspoint Switch |
發布緊急采購，3分鐘左右您將得到回復。