63
Absolute Maximum Ratings
T
A
= 25
o
C
Thermal Information
Maximum Supply Voltages
V
CC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.5V to +7V
V
CC
- V
BAT
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90V
Relay Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-0.5V to +15V
Operating Conditions
Temperature Range
HC55171IM, HC55171IB . . . . . . . . . . . . . . . . . . . . -40
o
C to 85
o
C
HC55171CM, HC55171CB . . . . . . . . . . . . . . . . . . . .0
o
C to 75
o
C
Relay Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .+5V to +12V
Positive Power Supply, V
CC
. . . . . . . . . . . . . . . . . . . . . . . . +5V
±
5%
Negative Power Supply, V
BAT
. . . . . . . . . . . . . . . . . . . .-16V to -80V
Thermal Resistance (Typical, Note 1)
PLCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Junction Temperature Plastic . . . . . . . . . . . . . . . . .150
o
C
Maximum Storage Temperature Range. . . . . . . . . . -65
o
C to 150
o
C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . .300
o
C
(SOIC, PLCC - Lead Tips Only)
θ
JA
(
o
C/W)
55
70
Die Characteristics
Transistor Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .224
Diode Count. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Die Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175 x 144
Substrate Potential. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .V
BAT
Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Bipolar-DI
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied
NOTE:
1.
θ
JA
is measured with the component mounted on an evaluation PC board in free air.
Electrical Specifications
Unless Otherwise Specified, Typical Parameters are at T
A
= 25
o
C, Min-Max Parameters are over
Operating Temperature Range, V
BAT
= -24V, V
CC
= +5V, AGND = BGND = 0V. All AC Parameters are specified
at 600
2-Wire terminating impedance.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
RINGING TRANSMISSION PARAMETERS
V
RING
Input Impedance
(Note 2)
-
5.4
-
k
4-Wire to 2-Wire Gain
V
RING
to V
T-R
(Note 2)
-
40
-
V/V
AC TRANSMISSION PARAMETERS
RX Input Impedance
300Hz to 3.4kHz (Note 2)
-
108
-
k
OUT1 Positive Output Voltage Swing
R
L
= 10k
(Note 2)
+2.5
-
-
V
OUT1 Negative Output Voltage Swing
R
L
= 10k
(Note 2)
-4.5
-
-
V
4-Wire Input Overload Level
300Hz to 3.4kHz R
L
= 1200
, 600
Reference
(Note 2)
-
+3.1
-
V
PEAK
2-Wire Return Loss
Matched for 600
, f = 300Hz (Note 2)
37
-
-
dB
Matched for 600
, f = 1000Hz (Note 2)
40
-
-
dB
Matched for 600
, f = 3400Hz (Note 2)
30
-
-
dB
2-Wire Longitudinal to Metallic Balance
Off Hook
Per ANSI/IEEE STD 455-1976 300Hz to 3400Hz
(Note 2)
58
63
-
dB
4-Wire Longitudinal Balance Off Hook
300Hz to 3400Hz (Note 2)
-
55
-
dB
Longitudinal Current Capability
I
LINE
= 40mA, T
A
= 25
o
C (Note 2)
-
40
-
mA
RMS
Insertion Loss, 2W-4W
0dBmO, 1kHz, Includes Tranhybrid Amp Gain = 3
-
±
0.05
±
0.2
dB
Insertion Loss, 4W-2W
0dBmO,1kHz
-
±
0.05
±
0.2
dB
Insertion Loss, 4W-4W
0dBmO, 1kHz, Includes Tranhybrid Amp Gain = 3
-
-
±
0.25
dB
Frequency Response
300Hz to 3400Hz Referenced to Absolute Level
at 1kHz, 0dBm Referenced 600
-
±
0.02
±
0.06
dB
HC55171