- 您現在的位置：買賣IC網 > PDF目錄371783 > HCS473-SLSQTP (Microchip Technology Inc.) Code Hopping Encoder and Transponder PDF資料下載
參數資料
| 型號： | HCS473-SLSQTP |
| 廠商： | Microchip Technology Inc. |
| 英文描述： | Code Hopping Encoder and Transponder |
| 中文描述： | 跳碼編碼器和轉發器 |
| 文件頁數： | 16/68頁 |
| 文件大小： | 1629K |
| 代理商： | HCS473-SLSQTP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
HCS473
DS40035C-page 14
Preliminary
2002 Microchip Technology Inc.
3.1.4
ENCODER MODE OPTIONS
The following HCS473 configuration options configure
transmission characteristics of the information exiting
the DATA pin:
Modulation select (MSEL)
Header select (HSEL)
Extended serial number (XSER)
Queue counter enable (QUEN)
Counter select (CNTSEL)
Low voltage trip point (VLOWSEL)
PLL interface select (AFSK)
RF enable output (RFEN)
Seed button code (SDBT)
Time before Seed (SDTM)
Limited Seed (SDLM)
Seed mode (SDMD)
RF baud rate select (RFBSL)
Guard time select (GSEL)
Minimum code words (MTX)
Timeout select (TSEL)
Long preamble enable (LPRE)
Long preamble length (LPRL)
Preamble duty cycle (PRD)
The following sections detail each configuration’s avail-
able options. All timing values specified are subject to
the specified oscillator variation.
3.1.4.1
Modulation Format (MSEL)
The Modulation format option selects the modulation
format for data output from the DATA pin; most often
transmitted via RF.
MSEL options:
Pulse Width Modulation (PWM), Figure 3-3
Manchester Modulation, Figure 3-4
3.1.4.2
Header Select (HSEL)
The synchronization header is typically used by the
receiver to adjust bit sampling appropriate to the trans-
mitter’s current speed; as the transmitter’s RC oscilla-
tor varies with temperature and voltage, so will the
transmission’s timing.
HSEL options:
4 RF
TE
10 RF
TE
3.1.4.3
Extended Serial Number (XSER)
The Extended Serial Number option determines
whether the HCS473 transmits a 28 or 32-bit serial
number.
When configured for a 28-bit serial number, the Most
Significant nibble of the 32 bits reserved for the serial
number is replaced with a copy of the 4-bit button sta-
tus, Figure 3-2.
XSER options:
28-bit serial number
32-bit serial number
3.1.4.4
Queue Counter (QUEN)
The QUE counter can be used to request secondary
decoder functions using only a single transmitter but-
ton. Typically a decoder must keep track of incoming
transmissions to determine when a double button press
occurs, perhaps an unlock all doors request. The QUE
counter removes this burden from the decoder by
counting multiple button presses and including the
QUE counter value in the last two bits of the 69-bit code
word, (Figure 3-2). If QUEN is disabled, the transmis-
sion will consist only of 67 bits as the QUE bits field is
not transmitted.
Que counter functionality is enabled with the QUEN
configuration option. The 2-bit QUE counter is incre-
mented each time an active button input is released for
at least the Debounce Time (T
DB
), then re-activated
(button pressed again) within the Queue Time (T
QUE
),
Figure 3-5. The counter increments up from 0 to a max-
imum of 3, returning to 0 only after a different button
activation or after button activations spaced greater
than the Queue Time (T
QUE
) apart.
The current transmission aborts, after completing the
minimum number of code words (Section 3.1.4.15),
when the active button inputs are released. A button re-
activation within the queue time (T
QUE
) then initiates a
new transmission (new synchronization counter,
encrypted data) using the updated QUE value. Button
combinations are queued the same as individual but-
tons.
相關PDF資料 |
PDF描述 |
|---|---|
| HCS473IPQTP | Code Hopping Encoder and Transponder |
| HCS473IPROM | Code Hopping Encoder and Transponder |
| HCS473IPSQTP | Code Hopping Encoder and Transponder |
| HCS473ISLQTP | Code Hopping Encoder and Transponder |
| HCS473ISLROM | IC EEPROM SRL 1024X16BIT 8DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HCS473T/SL | 功能描述:編碼器、解碼器、復用器和解復用器 w/ Passive Entry RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| HCS473T-I/SL | 功能描述:編碼器、解碼器、復用器和解復用器 w/ Passive Entry RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
| HCS4870C | 制造商:Power-One 功能描述:POWER SUPPLY |
| HCS500 | 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Programming Specification |
| HCS500/P | 功能描述:編碼器、解碼器、復用器和解復用器 3 fnc RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。