參數資料
型號： HCS473-SLSQTP
廠商： Microchip Technology Inc.
英文描述： Code Hopping Encoder and Transponder
中文描述： 跳碼編碼器和轉發器
文件頁數： 34/68頁
文件大?。?/td> 1629K
代理商： HCS473-SLSQTP
HCS473
DS40035C-page 32
Preliminary
2002 Microchip Technology Inc.
FIGURE 3-20:
LF DATA RESPONSE ADJUSTMENTS (LFRSP=1)
FIGURE 3-21:
LF COMMUNICATION ANALOG DELAYS
3.2.7
RECEIVE STABILITY -
CALCULATING COMMUNICATION
T
E
The HCS473’s internal oscillator may vary ±10% over
the device’s rated voltage and temperature range for
commercial temperature devices. A certain percentage
of industrial temperature devices vary further on the
slow side, -20%, when used at higher voltages (V
DD
>
3.5V) and cold temperature. When the internal oscilla-
tor varies, both its transmitted T
E
and expected T
E
when receiving will vary.
The HCS473 receive capability is ensured over a ±10%
oscillator variance, with receive capability no longer
robust as oscillator variance approaches ±15%. Indus-
trial devices operating at V
DD
voltages greater than
3.5V (and cold temperature) are therefore not guaran-
teed to be able to properly receive when communicated
to using an exact T
E
. When designing for these specific
operating conditions, the system designer must imple-
ment a method to adjust communication timing to the
speed of the HCS473.
Communication reliability with the transponder may be
improved by the transponder reader calculating the
HCS473’s T
E
from the Field Acknowledge sequence
and using this exact time element in communication to
and in reception routines from the transponder.
Always begin and end the time measurement on rising
edges. Whether LF or RF, the falling edge decay rates
may vary but the rising edge relationships should
remain consistent. A common T
E
calculation method
would be to time an 8T
E
sequence from the first Field
Acknowledge, then divide the value down to determine
the single T
E
value. An 8 T
E
measurement will give
good resolution and may be easily right-shifted (divide
by 2) three times for the math portion of the calculation
(Figure 3-22).
IFF, Read and Request Hop
CRC
P
H
R
(
F
(
RF Response (RFRSP=1)
Inductive
(LC Pins)
RF Response
(DATA Pin)
M
L
32-Bit LF Response (LFRSP=1)
T
FINH
1 LF
TE
Next
Command
T
CMD
T
CMD
Resulting 125 kHz on
Transponder Reader
Antenna (TX)
Digital Representation
of Communication from
Transponder Reader
600
μ
s
400
μ
s
Resulting 125 kHz on
Transponder Card
Antenna (RX)
Resulting digital signal
processed by
HCS473,
after analog filter
600
μ
s
400
μ
s
T
FILTR
T
FILTF
T
ANTR
T
ANTF
Bit ‘1’, 200
μ
s
LF
TE
Bit ‘0’, 200
μ
s
LF
TE
相關PDF資料
PDF描述
HCS473IPQTP Code Hopping Encoder and Transponder
HCS473IPROM Code Hopping Encoder and Transponder
HCS473IPSQTP Code Hopping Encoder and Transponder
HCS473ISLQTP Code Hopping Encoder and Transponder
HCS473ISLROM IC EEPROM SRL 1024X16BIT 8DIP
相關代理商/技術參數
參數描述
HCS473T/SL 功能描述:編碼器、解碼器、復用器和解復用器 w/ Passive Entry RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
HCS473T-I/SL 功能描述:編碼器、解碼器、復用器和解復用器 w/ Passive Entry RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
HCS4870C 制造商:Power-One 功能描述:POWER SUPPLY
HCS500 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Memory Programming Specification
HCS500/P 功能描述:編碼器、解碼器、復用器和解復用器 3 fnc RoHS:否 制造商:Micrel 產品:Multiplexers 邏輯系列:CMOS 位數: 線路數量（輸入/輸出）:2 / 12 傳播延遲時間:350 ps, 400 ps 電源電壓-最大:2.625 V, 3.6 V 電源電壓-最小:2.375 V, 3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-44 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*