- 您現在的位置：買賣IC網 > PDF目錄371785 > HCTS08KMSR (INTERSIL CORP) Radiation Hardened Quad 2-Input AND Gate PDF資料下載
參數資料
| 型號： | HCTS08KMSR |
| 廠商： | INTERSIL CORP |
| 元件分類： | 通用總線功能 |
| 英文描述： | Radiation Hardened Quad 2-Input AND Gate |
| 中文描述： | HCT SERIES, QUAD 2-INPUT AND GATE, CDFP14 |
| 封裝： | CERAMIC, DFP-14 |
| 文件頁數： | 10/10頁 |
| 文件大小： | 159K |
| 代理商： | HCTS08KMSR |
10
HCTS08MS
Spec Number
518842
NOTES:
1. Index area: A notch or a pin one identification mark shall be locat-
ed adjacent to pin one and shall be located within the shaded
area shown. The manufacturer’s identification shall not be used
as a pin one identification mark. Alternately, a tab (dimension k)
may be used to identify pin one.
2. If a pin one identification mark is used in addition to a tab, the lim-
its of dimension k do not apply.
3. This dimension allows for off-center lid, meniscus, and glass
overrun.
4. Dimensions b1 and c1 apply to lead base metal only. Dimension
M applies to lead plating and finish thickness. The maximum lim-
its of lead dimensions b and c or M shall be measured at the cen-
troid of the finished lead surfaces, when solder dip or tin plate
lead finish is applied.
5. N is the maximum number of terminal positions.
6. Measure dimension S1 at all four corners.
7. For bottom-brazed lead packages, no organic or polymeric mate-
rials shall be molded to the bottom of the package to cover the
leads.
8. Dimension Q shall be measured at the point of exit (beyond the
meniscus) of the lead from the body. Dimension Q minimum
shall be reduced by 0.0015 inch (0.038mm) maximum when sol-
der dip lead finish is applied.
9. Dimensioning and tolerancing per ANSI Y14.5M - 1982.
10. Controlling dimension: INCH.
-D-
-C-
0.004
H A - B
M
D
S
S
-A-
-B-
0.036
H A - B
M
D
S
S
e
E
A
Q
L
D
A
A
E1
SEATING AND
BASE PLANE
L
E2
E3
E3
-H-
b
C
S1
M
c1
b1
(c)
(b)
SECTION A-A
BASE
METAL
LEAD FINISH
PIN NO. 1
ID AREA
M
K14.B
14 LEAD CERAMIC METAL SEAL FLATPACK PACKAGE
SYMBOL
INCHES
MILLIMETERS
NOTES
MIN
MAX
MIN
MAX
A
0.045
0.115
1.14
2.92
-
b
0.015
0.022
0.38
0.56
-
b1
0.015
0.019
0.38
0.48
-
c
0.003
0.009
0.08
0.23
-
c1
0.003
0.007
0.08
0.18
-
D
-
0.390
-
9.91
3
E
0.235
0.260
5.97
6.60
-
E1
-
0.290
-
7.11
3
E2
0.125
-
3.18
-
-
E3
0.030
-
0.76
-
7
e
0.050 BSC
1.27 BSC
-
k
0.008
0.015
0.20
0.38
2
L
0.270
0.370
6.86
9.40
-
Q
0.010
0.020
0.25
0.51
8
S1
0.005
-
0.13
-
6
M
-
0.0015
-
0.04
-
N
14
14
-
Rev. 0 6/14/94
Packaging
(Continued)
相關PDF資料 |
PDF描述 |
|---|---|
| HCTS109HMSR | Radiation Hardened Dual JK Flip Flop |
| HCTS109DMSR | Radiation Hardened Dual JK Flip Flop |
| HCTS109DTR | Radiation Hardened Dual JK Flip Flop |
| HCTS109KMSR | Radiation Hardened Dual JK Flip Flop |
| HCTS109MS | Dual Positive-Edge-Triggered D-Type- Flip-Flops With Clear And Preset 14-CDIP -55 to 125 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HCTS08MS | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Radiation Hardened Quad 2-Input AND Gate |
| HCTS109D | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Radiation Hardened Dual JK Flip Flop |
| HCTS109DMSR | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Radiation Hardened Dual JK Flip Flop |
| HCTS109DTR | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Radiation Hardened Dual JK Flip Flop |
| HCTS109HMSR | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Radiation Hardened Dual JK Flip Flop |
發布緊急采購，3分鐘左右您將得到回復。