- 您現在的位置：買賣IC網 > PDF目錄370460 > HD404652 (Hitachi,Ltd.) 4-Bit Single-Chip Microcomputer PDF資料下載
參數資料
| 型號： | HD404652 |
| 廠商： | Hitachi,Ltd. |
| 英文描述： | 4-Bit Single-Chip Microcomputer |
| 中文描述： | 4位單片機 |
| 文件頁數： | 71/109頁 |
| 文件大小： | 430K |
| 代理商： | HD404652 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁當前第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁
HD404654 Series
71
Transmit Clock Error Detection (In External Clock Mode):
Serial interface 1 will malfunction if a
spurious pulse caused by external noise conflicts with a normal transmit clock during transfer. A transmit
clock error of this type can be detected as shown in figure 55.
If more than eight transmit clocks are input in transfer state, at the eighth clock including a spurious pulse
by noise, the octal counter reaches 000, the serial 1 interrupt request flag (IFS1: $003, bit 2) is set, and
transmit clock wait state is entered. At the falling edge of the next normal clock signal, the transfer state is
entered. After the transfer is completed and IFS is reset, writing to serial mode register 1A (SM1A: $005)
changes the state from transfer to STS wait. At this time serial interface 1 is in the transfer state, and the
serial 1 interrupt request flag (IFS1: $003, bit 2) is set again, and therefore the error can be detected.
Notes on Use:
Initialization after writing to registers: If port mode register A (PMRA: $004) is written to in transmit
clock wait state or in transfer state, serial interface 1 must be initialized by writing to serial mode
register 1A (SM1A: $005) again.
Serial 1 interrupt request flag (IFS1: $003, bit 2) set: For serial interface 1, if the state is changed from
transfer state to another by writing to serial mode register 1A (SM1A: $005) or executing the STS
instruction during the first low pulse of the transmit clock, the serial 1 interrupt request flag (IFS1:
$003, bit 2) is not set. To set the serial 1 interrupt request flag (IFS1: $003, bit 2), a serial mode register
1A (SM1A: $005) write or STS instruction execution must be programmed to be executed after
confirming that the
SCK
1
pin is at 1, that is, after executing the input instruction to port R4.
相關PDF資料 |
PDF描述 |
|---|---|
| HD404652H | RES T 0.2E 5W 1% |
| HD404652S | 4-Bit Single-Chip Microcomputer |
| HD404654 | RESISTOR, 0.10 OHM 5W |
| HD404654H | 4-Bit Single-Chip Microcomputer |
| HD404654S | 4-Bit Single-Chip Microcomputer |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HD404652H | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-Bit Single-Chip Microcomputer |
| HD404652S | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-Bit Single-Chip Microcomputer |
| HD404654 | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-Bit Single-Chip Microcomputer |
| HD404654H | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-Bit Single-Chip Microcomputer |
| HD404654S | 制造商:HITACHI 制造商全稱:Hitachi Semiconductor 功能描述:4-Bit Single-Chip Microcomputer |
發布緊急采購，3分鐘左右您將得到回復。