- 您現在的位置：買賣IC網 > PDF目錄371808 > HFBR-5320 200 MBd Low-Cost SBCON Multimode Fiber Transceiver(200 MBd 低價格SBCON 多模式光纖收發器) PDF資料下載
參數資料
| 型號： | HFBR-5320 |
| 英文描述： | 200 MBd Low-Cost SBCON Multimode Fiber Transceiver(200 MBd 低價格SBCON 多模式光纖收發器) |
| 中文描述： | 200 MBd的低成本SBCON多模光纖收發器（200 MBd的低價格SBCON多模式光纖收發器） |
| 文件頁數： | 8/8頁 |
| 文件大?。?/td> | 162K |
| 代理商： | HFBR-5320 |
Notes:
1. Resistance is in Ohms. Capacitance is in microfarads. Inductance is in microhenries.
2. Terminal transmitter input Data and Data-bar at the transmitter input pins. Terminate the receiver Output Data, Data-bar, Status
Flag, and Status Flag-bar at the follow-on device input pins. For lower power dissipation in the Status Flag termination circuitry
with small compromise to the signal quality, each Status Flag output can be loaded with 510 Ohms to ground instead of the two
resistor, split -load PECL termination shown in the Figure 3 schematic.
3. Make differential signal paths short and same length with equal termination impedance.
4. Signal traces should be 50 Ohms microstrip or stripline transmission lines. Use multilayer, ground-plane printed circuit board for
best high-frequency performance.
5. Use high-frequency, monolithic ceramic bypass capacitors and low series dc resistance inductors. Recommend use of surface-
mount coil inductors and capacitors. In low noise power supply systems, ferrite bead inductors can be substituted for coil
inductors. Locate power supply filter components close to their respective power supply pins.
6. Device ground pin should be directly and individually connected to ground.
7. Caution: Do not directly connect the fiber-optic module PECL outputs (Data, Data-bar, Status flag, Status Flag-bar, V
BB
) to ground
without proper current limiting impedance.
Figure 3.
V
BB
+5 V
0.1 μF
82
82
130
130
+5 V
0.1 μF
82
82
130
130
+5 V
0.1 μF
82
130
82
130
0.1 μF
0.1 μF
+5 V
TD
TD
RD
RD
SF
SF
0.1 μF
10 μF
GND
GND
GND
GND
GND
GND
DATA
DATA
GND
V
CC
GND
NC
V
CC
DATA
DATA
GND
GND
V
CC
V
CC
GND
SF
SF
GND
GND
GND
GND
GND
1
7
40
34
14
21
27
20
4 X 7 PINS
REQUIRED
HFBR-5320
(TOP VIEW)
NC = NO INTERNAL CONNECTION
1 μH
1 μH
www.semiconductor.agilent.com
Data subject to change.
Copyright 1999 Agilent Technologies, Inc.
5965-5256E (11/99)
相關PDF資料 |
PDF描述 |
|---|---|
| HFBR-5527 | 125 Megabaud Fiber Optic Transceiver(125 百萬波特光纖收發器) |
| HFBR-5710L | Small Form Factor Pluggable Optical Transceiver for Gigabit |
| HFBR-5710LP | Small Form Factor Pluggable Optical Transceiver for Gigabit |
| HFCT-5202 | 155 Mb/s Single Mode Fiber Transceiver with Integrated Clock and Data Recovery for ATM, SONET OC-3/SDH STM-1(應用于ATM, SONET OC-3/SDH STM-1帶集成時鐘和數據恢復的155 Mb/s單模式光收發器) |
| HFD2 | SUBMINIATURE DIP RELAY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HFBR-5320Z | 功能描述:光纖發射器、接收器、收發器 200MBd Low Cost SBCO N MMF Txc RoHS RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| HFBR-53A3VEM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1 x 9 3.3V Fiber Optic Transceiver for Fibre Channel/Storage - Extended Shield. Metalized Housing |
| HFBR-53A3VEMZ | 制造商:Avago Technologies 功能描述:TX/RX OPTICAL FIBER 9PIN - Tape and Reel |
| HFBR-53A3VFM | 功能描述:光纖發射器、接收器、收發器 MM 1X9 3V FC Txcvr w ith Flush Shld RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
| HFBR-53A3VFMZ | 功能描述:光纖發射器、接收器、收發器 3V 1x9 Fc TXcvr FLUS H Shield ROHS RoHS:否 制造商:Omron Electronics 產品:Transmitters 數據速率:3.5 Gbps 波長:850 nm 最大工作溫度: 最小工作溫度: 封裝 / 箱體: 封裝: |
發布緊急采購，3分鐘左右您將得到回復。