- 您現在的位置：買賣IC網 > PDF目錄8543 > HI5628/6INZ (Intersil)IC DAC 8BIT 60MSPS DUAL 48-LQFP PDF資料下載
參數資料
| 型號： | HI5628/6INZ |
| 廠商： | Intersil |
| 文件頁數： | 9/10頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 8BIT 60MSPS DUAL 48-LQFP |
| 標準包裝： | 250 |
| 位數： | 8 |
| 數據接口： | 并聯 |
| 轉換器數目： | 2 |
| 電壓電源： | 模擬和數字 |
| 功率耗散（最大）： | 330mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-LQFP |
| 供應商設備封裝： | 48-TQFP（7x7） |
| 包裝： | 托盤 |
| 輸出數目和類型： | 4 電流，單極 |
| 采樣率（每秒）： | 60M |
8
Definition of Specifications
Integral Linearity Error, INL, is the measure of the worst
case point that deviates from a best fit straight line of data
values along the transfer curve.
Differential Linearity Error, DNL, is the measure of the
step size output deviation from code to code. Ideally the step
size should be 1 LSB. A DNL specification of 1 LSB or less
guarantees monotonicity.
Output Settling Time, is the time required for the output
voltage to settle to within a specified error band measured
from the beginning of the output transition. The
measurement was done by switching from code 0 to 64, or
quarter scale. Termination impedance was 25 due to the
parallel resistance of the output 50 and the oscilloscope’s
50 input. This also aids the ability to resolve the specified
error band without overdriving the oscilloscope.
Singlet Glitch Area, is the switching transient appearing on
the output during a code transition. It is measured as the
area under the overshoot portion of the curve and is
expressed as a Volt-Time specification.
Full Scale Gain Error, is the error from an ideal ratio of 32
between the output current and the full scale adjust current
(through RSET).
Full Scale Gain Drift, is measured by setting the data inputs
to all ones and measuring the output voltage through a
known resistance as the temperature is varied from TMIN to
TMAX. It is defined as the maximum deviation from the value
measured at room temperature to the value measured at
either TMIN or TMAX. The units are ppm of FSR (Full Scale
Range) per degree C.
Total Harmonic Distortion, THD, is the ratio of the DAC output
fundamental to the RMS sum of the first five harmonics.
Spurious Free Dynamic Range, SFDR, is the amplitude
difference from the fundamental to the largest harmonically
or non-harmonically related spur within the specified
window.
Output Voltage Compliance Range, is the voltage limit
imposed on the output. The output impedance load should
be chosen such that the voltage developed does not violate
the compliance range.
Offset Error, is measured by setting the data inputs to all
zeros and measuring the output voltage through a known
resistance. Offset error is defined as the maximum deviation
of the output current from a value of 0mA.
Offset Drift, is measured by setting the data inputs to all
zeros and measuring the output voltage through a known
resistance as the temperature is varied from TMIN to TMAX.
It is defined as the maximum deviation from the value
measured at room temperature to the value measured at
either TMIN or TMAX. The units are ppm of FSR (Full Scale
Range) per degree C.
Power Supply Rejection, is measured using a single power
supply. Its nominal +5V is varied ±10% and the change in the
DAC full scale output is noted.
Reference Input Multiplying Bandwidth, is defined as the
3dB bandwidth of the voltage reference input. It is measured
by using a sinusoidal waveform as the external reference
with the digital inputs set to all 1s. The frequency is
increased until the amplitude of the output waveform is
0.707 of its original value.
Internal Reference Voltage Drift, is defined as the
maximum deviation from the value measured at room
temperature to the value measured at either TMIN or TMAX.
The units are ppm per degree C.
Detailed Description
The HI5628 is a dual, 8-bit, current out, CMOS, digital to
analog converter. Its maximum update rate is 125MSPS and
can be powered by either single or dual power supplies in
the recommended range of +3V to +5V. It consumes less
than 330mW of power when using a +5V supply with the
data switching at 100MSPS. The architecture is based on a
segmented current source arrangement that reduces glitch
by reducing the amount of current switching at any one time.
The five MSBs are represented by 31 major current sources
of equivalent current. The three LSBs are comprised of
binary weighted current sources. Consider an input pattern
to the converter which ramps through all the codes from 0 to
255. The three LSB current sources would begin to count up.
When they reached the all high state (decimal value of 7)
and needed to count to the next code, they would all turn off
and the first major current source would turn on. To continue
counting upward, the 3 LSBs would count up another 7
codes, and then the next major current source would turn on
and the three LSBs would all turn off. The process of the
single, equivalent, major current source turning on and the
three LSBs turning off each time the converter reaches
another 7 codes greatly reduces the glitch at any one
switching point. In previous architectures that contained all
binary weighted current sources or a binary weighted
resistor ladder, the converter might have a substantially
larger amount of current turning on and off at certain, worst-
case transition points such as midscale and quarter scale
transitions. By greatly reducing the amount of current
switching at certain ‘major’ transitions, the overall glitch of
the converter is dramatically reduced, improving settling
times and transient problems.
HI5628
相關PDF資料 |
PDF描述 |
|---|---|
| LT1253CS8#TR | IC AMP VID DUAL CURR FDBK 8SOIC |
| 207825-9 | CONN RCPT CPC 4POS STD SER 1 PCB |
| ISL5957IAZ | CONV D/A 14-BIT 3.3V 28-TSSOP |
| LT1253CS8 | IC AMP VIDEO LOW COST DUAL 8SOIC |
| 6-1437719-4 | CONN PLUG PIN 4POS SLD PNL MNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI5628EVAL1 | 功能描述:數據轉換 IC 開發工具 HI5628 EVALR D PLATFORM FOR LQFP RoHS:否 制造商:Texas Instruments 產品:Demonstration Kits 類型:ADC 工具用于評估:ADS130E08 接口類型:SPI 工作電源電壓:- 6 V to + 6 V |
| HI5628IN | 功能描述:DAC DUAL 8BIT 125MSPS 48LQFP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| HI5628INZ | 功能描述:數模轉換器- DAC D/A DL 8-BIT 125MSPS 48 LQFP IND TEMP RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| HI5630 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Triple 8-Bit, 80MSPS A/D Converter with Internal Voltage Reference |
| HI5630/8CN | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
發布緊急采購，3分鐘左右您將得到回復。