- 您現在的位置：買賣IC網 > PDF目錄9758 > HI5766KCA (Intersil)IC ADC 10-BIT 60MSPS 28-SSOP PDF資料下載
參數資料
| 型號： | HI5766KCA |
| 廠商： | Intersil |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 10-BIT 60MSPS 28-SSOP |
| 標準包裝： | 48 |
| 位數： | 10 |
| 采樣率（每秒）： | 60M |
| 數據接口： | 并聯 |
| 轉換器數目： | 8 |
| 功率耗散（最大）： | 260mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 28-SSOP/QSOP |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，單極；1 個差分，雙極 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
13
The resistors, R, in Figure 26 are not absolutely necessary
but may be used as load setting resistors. A capacitor, C,
connected from VIN+ to VIN- will help filter any high
frequency noise on the inputs, also improving performance.
Values around 20pF are sufficient and can be used on AC
coupled inputs as well. Note, however, that the value of
capacitor C chosen must take into account the highest
frequency component of the analog input signal.
Analog Input, Single-Ended Connection
The configuration shown in Figure 27 may be used with a
single ended AC coupled input.
Again, assume the difference between VREF+, typically
2.5V, and VREF-, typically 2V, is 0.5V. If VIN is a 1VP-P
sinewave, then VIN+ is a 1VP-P sinewave riding on a
positive voltage equal to VDC. The converter will be at
positive full scale when VIN+ is at VDC + 0.5V (VIN+ - VIN-
= +0.5V) and will be at negative full scale when VIN+ is
equal to VDC - 0.5V (VIN+ - VIN- = -0.5V). Sufficient
headroom must be provided such that the input voltage
never goes above +5V or below AGND. In this case, VDC
could range between 0.5V and 4.5V without a significant
change in ADC performance. The simplest way to produce
VDC is to use the DC bias source, VDC, output of the
HI5766.
The single ended analog input can be DC coupled
(Figure 28) as long as the input is within the analog input
common mode voltage range.
The resistor, R, in Figure 28 is not absolutely necessary but
may be used as a load setting resistor. A capacitor, C,
connected from VIN+ to VIN- will help filter any high
frequency noise on the inputs, also improving performance.
Values around 20pF are sufficient and can be used on AC
coupled inputs as well. Note, however, that the value of
capacitor C chosen must take into account the highest
frequency component of the analog input signal.
A single ended source may give better overall system
performance if it is first converted to differential before driving
the HI5766.
Digital Output Control and Clock Requirements
The HI5766 provides a standard high-speed interface to
external TTL logic families.
In order to ensure rated performance of the HI5766, the duty
cycle of the clock should be held at 50%
±5%. It must also
have low jitter and operate at standard TTL levels.
Performance of the HI5766 will only be guaranteed at
conversion rates above 1 MSPS. This ensures proper
performance of the internal dynamic circuits. Similarly, when
power is first applied to the converter, a maximum of 20
cycles at a sample rate above 1 MSPS will have to be
performed before valid data is available.
A Data Format Select (DFS) pin is provided which will
determine the format of the digital data outputs. When at
logic low, the data will be output in offset binary format.
When at logic high, the data will be output in two’s
complement format. Refer to Table 1 for further information.
VIN+
VIN-
HI5766
VIN
VDC
R
FIGURE 27. AC COUPLED SINGLE ENDED INPUT
VIN+
VIN-
HI5766
VDC
R
C
VIN
VDC
FIGURE 28. DC COUPLED SINGLE ENDED INPUT
HI5766
相關PDF資料 |
PDF描述 |
|---|---|
| V375C15M150B | CONVERTER MOD DC/DC 15V 150W |
| MS27656E17B99PA | CONN RCPT 23POS WALL MNT W/PINS |
| MC10EP16VADG | IC RCVR/DRVR HV ECL DIFF 8SOIC |
| V375C12M150BG2 | CONVERTER MOD DC/DC 12V 150W |
| M83723/86A08037 | CONN PLUG 3POS STRAIGHT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HI5766KCAZ | 功能描述:模數轉換器 - ADC A/D 10-BIT 60MSPS 28 SSOP COM TEMP RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| HI5766KCB | 功能描述:CONV A/D 10BIT 60MSPS 28-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| HI5766KCBS2503 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI5766KCBZ | 功能描述:模數轉換器 - ADC 28 COMTEMP A/D 10BIT 60MSPS RoHS:否 制造商:Texas Instruments 通道數量:2 結構:Sigma-Delta 轉換速率:125 SPs to 8 KSPs 分辨率:24 bit 輸入類型:Differential 信噪比:107 dB 接口類型:SPI 工作電源電壓:1.7 V to 3.6 V, 2.7 V to 5.25 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:VQFN-32 |
| HI5767 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:10-Bit, 20/40/60MSPS A/D Converter with Internal Voltage Reference |
發布緊急采購，3分鐘左右您將得到回復。