- 您現在的位置：買賣IC網 > PDF目錄371822 > HIP6304EVAL1 (Intersil Corporation) Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller PDF資料下載
參數資料
| 型號： | HIP6304EVAL1 |
| 廠商： | Intersil Corporation |
| 英文描述： | Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| 中文描述： | 微處理器核心電壓調節器的多相降壓PWM控制器 |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 176K |
| 代理商： | HIP6304EVAL1 |
4
Functional Pin Description
VID3 (Pin 1), VID2 (Pin 2), VID1 (Pin 3) and VID0
(Pin 4)
Voltage Identification inputs from microprocessor. These pins
respond to TTL and 3.3V logic signals. The HIP6304 decodes
VID bits to establish the output voltage. See Table 1.
EN (Pin 5)
Enable pin normal operation is with input open or high. A low
input disables the regulator and three states the PWM outputs.
COMP (Pin 6)
Output of the internal error amplifier. Connect this pin to the
external feedback and compensation network.
FB (Pin 7)
Inverting input of the internal error amplifier.
FS/DIS (Pin 8)
Channel frequency, F
SW
, select and disable. A resistor from
this pin to ground sets the switching frequency of the
converter. Pulling this pin to ground disables the converter
and three states the PWM outputs. See Figure 10.
GND (Pin 9)
Bias and reference ground. All signals are referenced to this
pin.
VSEN (Pin 10)
Power good monitor input. Connect to the microprocessor-
CORE voltage.
ISEN2 (Pin 11) and ISEN1 (Pin 14)
Current sense inputs from the individual converter channel’s
phase nodes.
PWM2 (Pin 12) and PWM1 (Pin 13)
PWM outputs for each driven channel in use. Connect these
pins to the PWM input of a HIP6601/2/3 driver.
PGOOD (Pin 15)
Power good. This pin provides a logic-high signal when the
microprocessor CORE voltage (VSEN pin) is within specified
limits and Soft-Start has timed out.
V
CC
(Pin 16)
Bias supply. Connect this pin to a 5V supply.
FIGURE 1. SIMPLIFIED BLOCK DIAGRAM OF THE HIP6304 VOLTAGE AND CURRENT CONTROL LOOPS FOR A TWO POWER
CHANNEL REGULATOR
CURRENT
SENSING
COMPARATOR
PWM
CIRCUIT
+
R
ISEN1
+
CORRECTION
ERROR
AMPLIFIER
FB
REFERENCE
DAC
I
SEN1
R
IN
V
CORE
Q3
Q4
L
02
PHASE
PWM1
I
L2
HIP6304
C
OUT
R
LOAD
V
IN
HIP6601
-
Q1
Q2
L
01
PHASE
I
L1
V
IN
HIP6601
CURRENT
SENSING
COMPARATOR
PWM
CIRCUIT
CORRECTION
PWM2
-
I AVERAGE
+
+
+
-
PROGRAMMABLE
R
ISEN2
I
SEN2
-
-
-
-
+
+
CURRENT
AVERAGING
∑
∑
∑
∑
VID3
VID2
VID1
VID0
EN
FS/DIS
VSEN
PGOOD
PWM1
PWM2
V
CC
FB
ISEN1
COMP
ISEN2
GND
14
15
16
9
13
12
11
10
1
2
3
4
5
7
6
8
HIP6304
相關PDF資料 |
PDF描述 |
|---|---|
| HIP6500B | Multiple Linear Power Controller with ACPI Control Interface |
| HIP6500BCB | Multiple Linear Power Controller with ACPI Control Interface |
| HIP6500BEVAL1 | Multiple Linear Power Controller with ACPI Control Interface |
| HIP6500 | Multiple Linear Power Controller with ACPI Control Interface |
| HIP6500CB | Multiple Linear Power Controller with ACPI Control Interface |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HIP6311 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| HIP6311_04 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| HIP6311A | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
| HIP6311ACB | 功能描述:IC REG CTRLR BUCK PWM 20-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
| HIP6311ACB-T | 功能描述:IC REG CTRLR BUCK PWM 20-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,000 系列:- PWM 型:電壓模式 輸出數:1 頻率 - 最大:1.5MHz 占空比:66.7% 電源電壓:4.75 V ~ 5.25 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:40-VFQFN 裸露焊盤 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。