- 您現在的位置：買賣IC網 > PDF目錄370743 > HYB 3117800BSJ-50 (SIEMENS AG) 2M×8-Bit Dynamic RAM (Fast Page Mode)(2M×8位 動態RAM(快速頁面模式)) PDF資料下載
參數資料
| 型號： | HYB 3117800BSJ-50 |
| 廠商： | SIEMENS AG |
| 英文描述： | 2M×8-Bit Dynamic RAM (Fast Page Mode)(2M×8位 動態RAM(快速頁面模式)) |
| 中文描述： | 200萬× 8位動態隨機存儲器（快速頁面模式）（2米× 8位動態隨機存儲器（快速頁面模式）） |
| 文件頁數： | 9/23頁 |
| 文件大小： | 178K |
| 代理商： | HYB 3117800BSJ-50 |
HYB 5(3)117800/BSJ-50/-60
2M
×
8 DRAM
Semiconductor Group
9
1998-10-01
Notes
1. All voltages are referenced to
V
SS
.
2.
I
CC1
,
I
CC3
,
I
CC4
and
I
CC6
depend on cycle rate.
3.
I
CC1
and
I
CC4
depend on output loading. Specified values are measured with the output open.
4. Address can be changed once or less while RAS =
V
IL
. In the case of
I
CC4
it can be changed once
or less during a fast page mode cycle (
t
PC
).
5. An initial pause of 200
μ
s is required after power-up followed by 8 RAS cycles of which at least
one cycle has to be a refresh cycle, before proper device operation is achieved. In case of using
internal refresh counter, a minimum of 8 CAS-before-RAS initialization cycles instead of 8 RAS
cycles are required.
6. AC measurements assume
t
T
= 5 ns.
7.
V
IH (MIN.)
and
V
IL (MAX.)
are reference levels for measuring timing of input signals. Transition times
are also measured between
V
IH
and
V
IL
.
8. Measured with a load equivalent to 2 TTL loads and 100 pF.
9. Operation within the
t
RCD (MAX.)
limit ensures that
t
RAC (MAX.)
can be met.
t
RCD (MAX.)
is specified as
a reference point only: If
t
RCD
is greater than the specified
t
RCD (MAX.)
limit, then access time is
controlled by
t
CAC
.
10.Operation within the
t
RAD (MAX.)
limit ensures that
t
RAC (MAX.)
can be met.
t
RAD (MAX.)
is specified as
a reference point only: If
t
RAD
is greater than the specified
t
RAD (MAX.)
limit, then access time is
controlled by
t
AA
.
11.Either
t
RCH
or
t
RRH
must be satisfied for a read cycle.
12.
t
OFF (MAX.)
and
t
OEZ (MAX.)
define the time at which the outputs achieve the open-circuit condition
and are not referenced to output voltage levels.
13.Either
t
DZC
or
t
DZO
must be satisfied.
14.Either
t
CDD
or
t
ODD
must be satisfied.
15.
t
WCS
,
t
RWD
,
t
CWD
,
t
AWD
and
t
CPWD
are not restrictive operating parameters. They are included in the
data sheet as electrical characteristics only. If
t
WCS
>
t
WCS (MIN.)
, the cycle is an early write cycle
and the I/O pin will remain open-circuit (high impedance) through the entire cycle; if
t
RWD
>
t
RWD (MIN.)
,
t
CWD
>
t
CWD (MIN.)
,
t
AWD
>
t
AWD (MIN.)
and
t
CPWD
>
t
CPWD (MIN.)
, the cycle is a read-write cycle
and I/O pins will contain data read from the selected cells. If neither of the above sets of
conditions is satisfied, the condition of the I/O pins (at access time) is indeterminate.
16.These parameters are referenced to the CAS leading edge in early write cycles and to the WE
leading edge in read-write cycles.
相關PDF資料 |
PDF描述 |
|---|---|
| HYB 5117800BSJ-50 | 2M×8-Bit Dynamic RAM (Fast Page Mode)(2M×8位 動態RAM(快速頁面模式)) |
| HYB 5117800BSJ-60 | 2M×8-Bit Dynamic RAM (Fast Page Mode)(2M×8位 動態RAM(快速頁面模式)) |
| HYB 5117800 | 2M×8-Bit Dynamic RAM (Fast Page Mode)(2M×8位 動態RAM(快速頁面模式)) |
| HYB 3117800BSJ-60 | 2M×8-Bit Dynamic RAM (Fast Page Mode)(2M×8位 動態RAM(快速頁面模式)) |
| HYB5117800BSJ-50- | 2M x 8 - Bit Dynamic RAM 2k Refresh |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HYB3117800BSJ-50 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:2M x 8-Bit Dynamic RAM |
| HYB3117800BSJ-60 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:2M x 8 - Bit Dynamic RAM 2k Refresh |
| HYB3117800BSJ-70 | 制造商:INFINEON 制造商全稱:Infineon Technologies AG 功能描述:2M x 8-Bit Dynamic RAM |
| HYB3117800BSJL-50 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Fast Page Mode DRAM |
| HYB3117800BSJL-60 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:x8 Fast Page Mode DRAM |
發布緊急采購，3分鐘左右您將得到回復。