- 您現在的位置：買賣IC網 > PDF目錄379208 > ICM7555CD (NXP Semiconductors N.V.) General purpose CMOS timer PDF資料下載
參數資料
| 型號： | ICM7555CD |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | 時鐘及定時 |
| 英文描述： | General purpose CMOS timer |
| 封裝： | ICM7555CD/01<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week 12, 2005,;ICM7555CD/01<SOT96-1 (SO8)|<<http://www.nxp.com/packages/SOT96-1.html<1<week |
| 文件頁數： | 18/22頁 |
| 文件大?。?/td> | 122K |
| 代理商： | ICM7555CD |
ICM7555_2
NXP B.V. 2009. All rights reserved.
Product data sheet
Rev. 02 — 3 August 2009
18 of 22
NXP Semiconductors
ICM7555
General purpose CMOS timer
For further information on temperature profiles, refer to Application Note AN10365
“Surface mount reflow soldering description”
14. Soldering of through-hole mount packages
14.1 Introduction to soldering through-hole mount packages
This text gives a very brief insight into wave, dip and manual soldering.
Wave soldering is the preferred method for mounting of through-hole mount IC packages
on a printed-circuit board.
14.2 Soldering by dipping or by solder wave
Driven by legislation and environmental forces the worldwide use of lead-free solder
pastes is increasing. Typical dwell time of the leads in the wave ranges from
3 seconds to 4 seconds at 250
°
C or 265
°
C, depending on solder material applied, SnPb
or Pb-free respectively.
The total contact time of successive solder waves must not exceed 5 seconds.
The device may be mounted up to the seating plane, but the temperature of the plastic
body must not exceed the specified maximum storage temperature (T
stg(max)
). If the
printed-circuit board has been pre-heated, forced cooling may be necessary immediately
after soldering to keep the temperature within the permissible limit.
14.3 Manual soldering
Apply the soldering iron (24 V or less) to the lead(s) of the package, either below the
seating plane or not more than 2 mm above it. If the temperature of the soldering iron bit is
less than 300
°
C it may remain in contact for up to 10 seconds. If the bit temperature is
between 300
°
C and 400
°
C, contact may be up to 5 seconds.
MSL: Moisture Sensitivity Level
Fig 19. Temperature profiles for large and small components
001aac844
temperature
time
minimum peak temperature
= minimum soldering temperature
maximum peak temperature
= MSL limit, damage level
peak
temperature
相關PDF資料 |
PDF描述 |
|---|---|
| ICM7555ID | General purpose CMOS timer |
| ICY7C1362C-166BGI | 9-Mbit (256K x 36/512K x 18) Pipelined SRAM |
| ICY7C1362C-166BZI | 9-Mbit (256K x 36/512K x 18) Pipelined SRAM |
| ICY7C1362C-166BGXI | 9-Mbit (256K x 36/512K x 18) Pipelined SRAM |
| ID100 | MONOLITHIC DUAL PICO AMPERE DIODES |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICM7555CD,602 | 功能描述:計時器和支持產品 CMOS TIMER RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| ICM7555CD,623 | 功能描述:計時器和支持產品 CMOS TIMER RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| ICM7555CD/01 | 功能描述:計時器和支持產品 CMOS TIMER 0 TO +70 RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| ICM7555CD/01,112 | 功能描述:計時器和支持產品 CMOS TIMER 0 TO +70 RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
| ICM7555CD/01,118 | 功能描述:計時器和支持產品 CMOS TIMER GEN-PURPOSE RoHS:否 制造商:Micrel 類型:Standard 封裝 / 箱體:SOT-23 內部定時器數量:1 電源電壓-最大:18 V 電源電壓-最小:2.7 V 最大功率耗散: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。