- 您現在的位置：買賣IC網 > PDF目錄360744 > ICS200 SMPTE Time Code Receiver/Generator PDF資料下載
參數資料
| 型號： | ICS200 |
| 英文描述： | SMPTE Time Code Receiver/Generator |
| 中文描述： | SMPTE時間碼接收器/發電機 |
| 文件頁數： | 6/21頁 |
| 文件大?。?/td> | 285K |
| 代理商： | ICS200 |
ICS2008B
6
ICS2008B Rev D 4/05/05
The SMPTE Status Register is a read only register which
contains video and LTC status.
FRAMEIN —
This bit indicates the state of the FRAME
input pin. It is used as an alternate source for B/A frame
status. This is useful when the quality of the video signal is
not good enough to extract the B/A frame status.
CLICK —
This bit indicates the state of the CLICK input
pin. It can be used as a synchronization source for the LTC
transmitter.
LTCLOCK —
When a valid forward or backward LTC sync
pattern is detected, this bit is set to one. It is reset to zero when
an expected LTC sync pattern is missed or an invalid LTC bit
is detected.
CODEDIR —
The code direction bit works in conjunction
with the LTCLOCK bit. When the LTCLOCK bit is set to one,
the CODEDIR bit is valid. Otherwise, it is not. See the table
below.
VLOCK —
This is a hardware driven bit which indicates that
genlock has been achieved with the selected video SYNC
source.
FRAME & FIELD —
The hardware SYNC separator detects
the field and frame from the selected video input. The even/
odd fields are identified by a 1/0 in bit 6. Bit 7, FRAME, is valid
for PAL video after line 6. Bit 6, FIELD, is valid after line 5 in
NTSC mode or line 2 in PAL mode.
The SMPTE2 register is the register which points to the 57
indirect registers. When reading or writing an indirect register,
the value in the ADDRESS pointer, SMPTE2 bits 5 to 0, is the
address of the register accessed through SMPTE3. If the
AUTOINC bit is set to one, at the end of an access cycle to
SMPTE3, ADDRESS will automatically increment. Otherwise,
ADDRESS holds its value.
SMPTE3 is the data register through which all of the indirect
registers are accessed. The address for a given register must
first be set in SMPTE2 before accessing that register.
Indirect Registers
The following describes the functions controlled by the
indirect registers. A map of the indirect registers follows this
section, on page 11.
LTC Read Registers
IR0-IR7
(read-only)
These read only registers contain the LTC data as received.
Both forward and backward frames are stored with LTC bit 0
in the LSB of IR0 and LTC bit 63 in the MSB of IR7.
LTC Write Registers
IR8-IRF
These registers contain the data to be sent by the LTC trans-
mitter. The LSB of IR8 is sent as LTC bit 0, and the MSB of
IRF is sent as LTC bit 63. The data is transmitted as it is stored
in IR8-IRF.
LTCLOCKCODEDIR
LTC RECEIVER STATUS
0
X
Looking for SYNC pattern
1
0
Receiving LTC (FORWARD)
1
1
Receiving LTC (BACKWARD)
SMPTE Status Register
FRAMEIN (input = 1-high, 0-low)
CLICK (input = 1-high, 0-low)
LTCLOCK (1-locked, 0-not locked)
CODEDIR (1-bkwd, 0-fwd)
Reserved
VLOCK (1-locked, 0-not locked)
FIELD
FRAME (PAL only)
7 6 5 4 3 2 1 0
SMPTE1
Indirect Address Register
ADDRESS
Reserved
AUTOINC (1-increment, 0-hold)
SMPTE2
7 6 5 4 3 2 1 0
Indirect Address Register
SMPTE3
7 6 5 4 3 2 1 0
相關PDF資料 |
PDF描述 |
|---|---|
| ICS2008BEP | SMPTE Time Code Receiver/Generator |
| ICS2008BY-10 | ER 35C 35#16 PIN PLUG |
| ICS2008BV | SMPTE Time Code Receiver/Generator |
| ICS2008BEB | SMPTE Time Code Receiver/Generator |
| ICS2101M | |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS2001M | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Digital-to-Analog Converter |
| ICS2001N | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Digital-to-Analog Converter |
| ICS2002 | 制造商:ICS 制造商全稱:ICS 功能描述:Wavedec Digital Audio Codec |
| ICS2002V | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Soundcard Circuits |
| ICS2002Y | 制造商:ICS 制造商全稱:ICS 功能描述:Wavedec Digital Audio Codec |
發布緊急采購，3分鐘左右您將得到回復。