- 您現在的位置：買賣IC網 > PDF目錄8976 > ICS841608AKILFT (IDT, Integrated Device Technology Inc)IC CLOCK GENERATOR 32-VFQFPN PDF資料下載
參數資料
| 型號： | ICS841608AKILFT |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 16/17頁 |
| 文件大小： | 0K |
| 描述： | IC CLOCK GENERATOR 32-VFQFPN |
| 產品培訓模塊： | PCI-Express |
| 標準包裝： | 2,500 |
| 系列： | HiPerClockS™, FemtoClock™ |
| 類型： | 時鐘發生器，扇出配送，多路復用器 |
| PLL： | 帶旁路 |
| 輸入： | LVCMOS，LVTTL，晶體 |
| 輸出： | HCSL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 2:8 |
| 差分 - 輸入:輸出： | 無/是 |
| 頻率 - 最大： | 125MHz |
| 除法器/乘法器： | 是/無 |
| 電源電壓： | 3.135 V ~ 3.465 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-VFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-VFQFPN 裸露焊盤（4x4） |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 841608AKILFT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁當前第16頁第17頁
IDT / ICS HCSL CLOCK GENERATOR
8
ICS841608AKI REV. A JUNE 18, 2008
ICS841608I
FEMTOCLOCKS CRYSTAL-TO-HCSL CLOCK GENERATOR
APPLICATION INFORMATION
As in any high speed analog circuitry, the power supply pins
are vulnerable to random noise. To achieve optimum jitter
performance, power supply isolation is required. The ICS841608I
provides separate power supplies to isolate any high switching
noise from the outputs to the internal PLL. V
DD and VDDA
should
be individually connected to the power supply plane through
vias, and 0.01F bypass capacitors should be used for each
pin.
Figure 1 illustrates this for a generic V
DD pin and also shows
that V
DDA requires that an additional10Ω resistor along with a
10F bypass capacitor be connected to the V
DDA pin.
POWER SUPPLY FILTERING TECHNIQUES
FIGURE 1. POWER SUPPLY FILTERING
10
Ω
V
DDA
10
μF
.01
μF
3.3V
.01
μF
V
DD
FIGURE 2. P.C.ASSEMBLY FOR EXPOSED PAD THERMAL RELEASE PATH –SIDE VIEW (DRAWING NOT TO SCALE)
VFQFN EPAD THERMAL RELEASE PATH
In order to maximize both the removal of heat from the package
and the electrical performance, a land patter n must be
incorporated on the Printed Circuit Board (PCB) within the footprint
of the package corresponding to the exposed metal pad or
exposed heat slug on the package, as shown in
Figure 2. The
solderable area on the PCB, as defined by the solder mask, should
be at least the same size/shape as the exposed pad/slug area on
the package to maximize the thermal/electrical performance.
Sufficient clearance should be designed on the PCB between the
outer edges of the land pattern and the inner edges of pad pattern
for the leads to avoid any shorts.
While the land pattern on the PCB provides a means of heat
transfer and electrical grounding from the package to the board
through a solder joint, thermal vias are necessary to effectively
conduct from the surface of the PCB to the ground plane(s). The
land pattern must be connected to ground through these vias.
The vias act as “heat pipes”. The number of vias (i.e. “heat pipes”)
are application specific and dependent upon the package power
dissipation as well as electrical conductivity requirements. Thus,
thermal and electrical analysis and/or testing are recommended
to determine the minimum number needed. Maximum thermal
and electrical performance is achieved when an array of vias is
incorporated in the land pattern. It is recommended to use as
many vias connected to ground as possible. It is also
recommended that the via diameter should be 12 to 13mils (0.30
to 0.33mm) with 1oz copper via barrel plating. This is desirable to
avoid any solder wicking inside the via during the soldering process
which may result in voids in solder between the exposed pad/
slug and the thermal land. Precautions should be taken to
eliminate any solder voids between the exposed heat slug and
the land pattern. Note: These recommendations are to be used
as a guideline only. For further information, refer to the Application
Note on the Surface Mount Assembly of Amkor’s Thermally/
Electrically Enhance Leadfame Base Package, Amkor Technology.
THERMAL VIA
LAND PATTERN
SOLDER
PIN
SOLDER
PIN PAD
PIN
GROUND PLANE
EXPOSED HEAT SLUG
(GROUND PAD)
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B40-MV-F2 | CONVERTER MOD DC/DC 5V 150W |
| VI-B4B-MY-F1 | CONVERTER MOD DC/DC 95V 50W |
| VI-B4B-MW-F4 | CONVERTER MOD DC/DC 95V 100W |
| ICS8402AKILF | IC FREQ SYNTHESIZER 32VFQFPN |
| AD5422BCPZ-REEL7 | IC DAC 16BIT SRL 40LFCSP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS841608AKIT | 功能描述:IC CLOCK GENERATOR 32-VFQFPN RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™, FemtoClock™ 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
| ICS841608I | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:FEMTOCLOCKS CRYSTAL-TO-HCSL CLOCK GENERATOR VCO: 500MHz |
| ICS841654AGI | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:FEMTOCLOCKS? CRYSTAL-TO-HCSL CLOCK GENERATOR |
| ICS841654AGILF | 功能描述:IC CLOCK GENERATOR 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™, FemtoClock™ 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
| ICS841654AGILFT | 功能描述:IC CLOCK GENERATOR 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™, FemtoClock™ 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
發布緊急采購，3分鐘左右您將得到回復。