- 您現在的位置：買賣IC網 > PDF目錄67690 > ICS8431AMI-21LF (INTEGRATED DEVICE TECHNOLOGY INC) 350 MHz, OTHER CLOCK GENERATOR, PDSO28 PDF資料下載
參數資料
| 型號： | ICS8431AMI-21LF |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 350 MHz, OTHER CLOCK GENERATOR, PDSO28 |
| 封裝： | 7.50 X 18.05 MM, 2.25 MM HEIGHT, ROHS COMPLIANT, MS-013, MO-119, SOIC-28 |
| 文件頁數： | 3/16頁 |
| 文件大?。?/td> | 256K |
| 代理商： | ICS8431AMI-21LF |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
8431AMI-21
www.icst.com/products/hiperclocks.html
REV. A AUGUST 2, 2005
11
Integrated
Circuit
Systems, Inc.
ICS8431I-21
350MHZ, LOW JITTER, CRYSTAL OSCILLATOR-
TO
-3.3V LVPECL FREQUENCY SYNTHESIZER
FIGURE 5B. PCB BOARD LAYOUT FOR ICS8431I-21
The following component footprints are used in this layout
example:
All the resistors and capacitors are size 0603.
POWER AND GROUNDING
Place the decoupling capacitors C1, C2 and C6, as close as
possible to the power pins. If space allows, placment of the
decoupling capacitor on the component side is preferred. This
can reduce unwanted inductance between the decoupling ca-
pacitor and the power pin generated by the via.
Maximize the power and ground pad sizes and number of vias
capacitors. This can reduce the inductance between the power
and ground planes and the component power and ground pins.
The RC filter consisting of R5, C3, and C4 should be placed as
close to the V
CCA pin as possible.
CLOCK TRACES AND TERMINATION
Poor signal integrity can degrade the system performance or
cause system failure. In synchronous high-speed digital systems,
the clock signal is less tolerant to poor signal integrity than other
signals. Any ringing on the rising or falling edge or excessive ring
back can cause system failure. The shape of the trace and the
trace delay might be restricted by the available space on the board
and the component location. While routing the traces, the clock
signal traces should be routed first and should be locked prior to
routing other signal traces.
The 50
Ω output trace pair should have same length.
Avoid sharp angles on the clock trace. Sharp angle turns
cause the characteristic impedance to change on the
transmission lines.
Keep the clock traces on the same layer. Whenever pos-
sible, avoid placing vias on the clock traces. Placement
of vias on the traces can affect the trace characteristic
impedance and hence degrade signal integrity.
To prevent cross talk, avoid routing other signal traces in
parallel with the clock traces. If running parallel traces is
unavoidable, allow a separation of at least three trace
widths between the differential clock trace and the other
signal trace.
Make sure no other signal traces are routed between the
clock trace pair.
The matching termination resistors should be located as
close to the receiver input pins as possible.
The matching termination resistors R1, R2, R3 and R4 should
be located as close to the receiver input pins as possible.
Other termination scheme can also be used but is not shown
in the example.
CRYSTAL
The crystal X1 should be located as close as possible to the pins
25 (XTAL_OUT) and 26 (XTAL_IN).The trace length between the
X1 and U1 should be kept to a minimum to avoid unwanted para-
sitic inductance and capacitance. Other signal traces should not
be routed near the crystal traces.
C4
Signals
X1
C3
VCC
GND
VIA
C1
Zo=50 Ohm
U1
Zo=50 Ohm
C2
C8
R5
C6
ICS8431-21
C7
相關PDF資料 |
PDF描述 |
|---|---|
| ICS8431CM-01LF | 200 MHz, OTHER CLOCK GENERATOR, PDSO28 |
| ICS8431CM-11T | 255 MHz, OTHER CLOCK GENERATOR, PDSO28 |
| ICS8431CM-11LFT | 255 MHz, OTHER CLOCK GENERATOR, PDSO28 |
| ICS8431DMI-01 | 200 MHz, OTHER CLOCK GENERATOR, PDSO28 |
| ICS8431DMI-01LFT | 200 MHz, OTHER CLOCK GENERATOR, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICS8431AMI-21LFT | 功能描述:IC SYNTHESIZER 350MHZ 28-SOIC RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:HiPerClockS™ 標準包裝:1,000 系列:- 類型:時鐘/頻率合成器，扇出分配 PLL:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 除法器/乘法器:- 電源電壓:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:56-VFQFN 裸露焊盤 供應商設備封裝:56-VFQFP-EP（8x8） 包裝:帶卷 (TR) 其它名稱:844S012AKI-01LFT |
| ICS8431AMI-21T | 制造商:ICS 制造商全稱:ICS 功能描述:350MHZ, LOW JITTER, CRYSTAL OSCILLATOR-TO-3.3V LVPECL FREQUENCY SYNTHESIZER |
| ICS8431CM-01 | 制造商:ICS 制造商全稱:ICS 功能描述:200MHZ, LOW JITTER, LVPECL FREQUENCY SYNTHESIZER |
| ICS8431CM-01T | 制造商:ICS 制造商全稱:ICS 功能描述:200MHZ, LOW JITTER, LVPECL FREQUENCY SYNTHESIZER |
| ICS8431CM-11 | 制造商:ICS 制造商全稱:ICS 功能描述:255MHZ, LOW JITTER, LVPECL FREQUENCY SYNTHESIZER |
發布緊急采購，3分鐘左右您將得到回復。