- 您現在的位置：買賣IC網 > PDF目錄360788 > ICSLV810FI Buffer/Clock Driver PDF資料下載
參數資料
| 型號： | ICSLV810FI |
| 英文描述： | Buffer/Clock Driver |
| 中文描述： | 緩沖器/時鐘驅動器 |
| 文件頁數： | 3/12頁 |
| 文件大?。?/td> | 145K |
| 代理商： | ICSLV810FI |
Buffer/Clock Driver
MDS LV810 F
3
Revision 101305
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
●
tel (408) 297-1201
●
www.icst.com
ICSLV810
External Components
The ICSLV810 requires a minimum number of external
components for proper operation.
Decoupling Capacitors
Decoupling capacitors of 0.01μF must be connected
between VDD and GND, as close to these pins as
possible. For optimum device performance, the
decoupling capacitors should be mounted on the
component side of the PCB. Avoid the use of vias in the
decoupling circuit.
Series Termination Resistor
When the PCB trace between the clock outputs and the
loads are over 1 inch, series termination should be
used. To series terminate a 50
trace (a commonly
used trace impedance) place a 33
resistor in series
with the clock line, as close to the clock output pin as
possible. The nominal impedance of the clock output is
20
.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
1) The 0.01μF decoupling capacitors should be
mounted on the component side of the board as close
to the VDD pins as possible. No vias should be used
between the decoupling capacitors and VDD pins. The
PCB trace to VDD pin should be kept as short as
possible, as should the PCB trace to the ground via.
2) To minimize EMI the 33
series termination resistor,
if needed, should be placed close to the clock output.
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the ICSLV810. These ratings,
which are standard values for ICS commercially rated parts, are stress ratings only. Functional operation of
the device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Recommended Operation Conditions
Item
Rating
Supply Voltage, VDD MAX
All Inputs and Outputs
Ambient Operating Temperature
Storage Temperature
Junction Temperature
Soldering Temperature
7 V
-0.5 V to VDDA + 1.2 V
-40 to +85
°
C
-65 to +150
°
C
125
°
C
260
°
C
Parameter
Ambient Operating Temperature
Power Supply Voltage (measured with respect to GND), VDDA
Power Supply Voltage (measured with respect to GND), VDDB
Power Supply Voltage (measured with respect to GND), VDDC
Min.
-40
1.425
1.425
1.425
Typ.
Max.
+85
2.625
2.625
2.625
Units
°
C
V
V
V
相關PDF資料 |
PDF描述 |
|---|---|
| ICSLV810FILF | Buffer/Clock Driver |
| ICSLV810FILFT | Buffer/Clock Driver |
| ICSLV810FIT | Buffer/Clock Driver |
| ICSLV810RI | Buffer/Clock Driver |
| ICSLV810RILF | Buffer/Clock Driver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ICSLV810FILF | 制造商:ICS 制造商全稱:ICS 功能描述:Buffer/Clock Driver |
| ICSLV810FILFT | 制造商:ICS 制造商全稱:ICS 功能描述:Buffer/Clock Driver |
| ICSLV810FIT | 制造商:ICS 制造商全稱:ICS 功能描述:Buffer/Clock Driver |
| ICSLV810RI | 制造商:ICS 制造商全稱:ICS 功能描述:Buffer/Clock Driver |
| ICSLV810RILF | 制造商:ICS 制造商全稱:ICS 功能描述:Buffer/Clock Driver |
發布緊急采購，3分鐘左右您將得到回復。