- 您現在的位置：買賣IC網 > PDF目錄377420 > IDT72511 (Integrated Device Technology, Inc.) High-Performance Current-Mode PWM Controller 8-SOIC 0 to 70 PDF資料下載
參數資料
| 型號： | IDT72511 |
| 廠商： | Integrated Device Technology, Inc. |
| 英文描述： | High-Performance Current-Mode PWM Controller 8-SOIC 0 to 70 |
| 中文描述： | 雙向并行FIFO的512 × 18 |
| 文件頁數： | 6/28頁 |
| 文件大?。?/td> | 434K |
| 代理商： | IDT72511 |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
5.32
6
IDT72511/IDT72521
BIDIRECTIONAL FIRST-IN FIRST-OUT MEMORY
MILITARY AND COMMERCIAL TEMPERATURE RANGES
When either of the internal FIFOs are accessed, 18 bits of
data are transferred across Port A. Since the bypass path is
only 9 bits wide, the least significant byte (D
A0
-D
A7,
D
A16
) is
used on Port A. All of the registers are 16 bits wide which
means only the data bits (D
A0
-D
A15
) are passed by Port A.
Bypass Path
The bypass path acts as a bidirectional bus transceiver
directly between Port A and Port B. The direct connection
requires that the Port A interface pins are inputs and the Port
B interface pins are outputs. The bypass path is 9 bits wide in
an 18- to 18-bit configuration or 18 bits wide in a 36- to 36-
bit configuration.
During bypass operations, the BiFIFOs must be pro-
grammed into peripheral interface mode. Bit 10 of Configura-
tion Register 5 (see Table 10) is set to
1
for peripheral
interface mode.
Command Register
Ten registers are accessible through Port A, a Command
Register, a Status Register, and eight Configuration
Registers.
Peripheral Interface Mode
If Port B is connected to a peripheral controller, all
BiFIFOs in the configuration must be programmed in peri-
pheral interface mode. In this mode, all the Port B interface
pins are all outputs. To assure fixed high states for
R
B
and
W
B
before they are programmed into an output, these two
pins should be pulled up to V
CC
with 10K resistors. Of
course, only one set of Port B interface pins should be used
to control a single peripheral device, while the other interface
pins are all ignored. Figure 2 shows a BiFIFO configuration
connected to a peripheral.
Port A Interface
The BiFIFO is straightforward to use in microprocessor-
based systems because each BiFIFO port has a standard
microprocessor control set. Port A has access to six re-
sources: the A
→
B FIFO, the B
→
A FIFO, the 9-bit direct data
bus (bypass path), the configuration registers, status and
command registers. The Port A Address and Read/Write
pins determine the resource being accessed as shown in
Table 1. Data Strobe is used to move data in and out of the
BiFIFO.
IDT
BiFIFO
Processor
Address
Peripheral
Controller
Cntl
Data
Data A Data B
Data
Cntl A
Cntl B
ACK
REQ
CLK
ACK
REQ
I/O
Data
IDT
BiFIFO
Data A Data B
Cntl
A
Cntl B
ACK
REQ
CLK
C
L
RAM
3
3
18
DMA or System
Clock
Control
36
18
36
2668 drw 06
Figure 2. 36-Bit Processor to 36-Bit Peripheral Configuration
NOTE:
1. 36- to 36-bit peripheral interface configuration. Upper BiFIFO only is used in 18- to 18-bit configuration. Note that
Cntl A
refers to
CS
A,
A
1
, A
0
, R/
W
A,
and
DS
A;
Cntl B
refers to R/
W
B
and
DS
B
or
R
B
and
W
B.
相關PDF資料 |
PDF描述 |
|---|---|
| IDT72511L25G | High-Performance Current-Mode PWM Controller 14-SOIC 0 to 70 |
| IDT72511L25GB | High-Performance Current-Mode PWM Controller 8-SOIC 0 to 70 |
| IDT72511L25J | High-Performance Current-Mode PWM Controller 14-SOIC 0 to 70 |
| IDT72511L25JB | High-Performance Current-Mode PWM Controller 8-SOIC 0 to 70 |
| IDT72511L35G | High-Performance Current-Mode PWM Controller 14-SOIC 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT72605L20J | 功能描述:IC FIFO BI SYNC 256X18 68-PLCC RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:7200 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433 |
| IDT72605L20J8 | 功能描述:IC FIFO BI SYNC 256X18 68-PLCC RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:7200 標準包裝:90 系列:7200 功能:同步 存儲容量:288K（16K x 18） 數據速率:100MHz 訪問時間:10ns 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:64-LQFP 供應商設備封裝:64-TQFP（14x14） 包裝:托盤 其它名稱:72271LA10PF |
| IDT72605L20PF | 功能描述:IC FIFO BI SYNC 256X18 64-TQFP RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:7200 標準包裝:15 系列:74F 功能:異步 存儲容量:256（64 x 4） 數據速率:- 訪問時間:- 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:24-DIP（0.300"，7.62mm） 供應商設備封裝:24-PDIP 包裝:管件 其它名稱:74F433 |
| IDT72605L20PF8 | 功能描述:IC FIFO BI SYNC 256X18 64-TQFP RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:7200 標準包裝:90 系列:7200 功能:同步 存儲容量:288K（16K x 18） 數據速率:100MHz 訪問時間:10ns 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:64-LQFP 供應商設備封裝:64-TQFP（14x14） 包裝:托盤 其它名稱:72271LA10PF |
| IDT72605L25J | 功能描述:IC FIFO BI SYNC 256X18 68-PLCC RoHS:否 類別:集成電路 (IC) >> 邏輯 - FIFO 系列:7200 標準包裝:90 系列:7200 功能:同步 存儲容量:288K（16K x 18） 數據速率:100MHz 訪問時間:10ns 電源電壓:4.5 V ~ 5.5 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:64-LQFP 供應商設備封裝:64-TQFP（14x14） 包裝:托盤 其它名稱:72271LA10PF |
發布緊急采購，3分鐘左右您將得到回復。