參數資料
型號： IDT82V3280PFG
廠商： IDT, Integrated Device Technology Inc
文件頁數： 58/171頁
文件大?。?/td> 0K
描述： IC PLL WAN SE STRATUM 2 100-TQFP
標準包裝： 1
類型： 時鐘/頻率發生器，多路復用器
PLL： 是
主要目的： 以太網，SONET/SDH，Stratum
輸入： CMOS，LVDS，PECL
輸出： CMOS，LVDS，PECL
電路數： 1
比率 - 輸入:輸出： 14:9
差分 - 輸入:輸出： 是/是
頻率 - 最大： 622.08MHz
電源電壓： 3 V ~ 3.6 V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 100-LQFP
供應商設備封裝： 100-TQFP（14x14）
包裝： 托盤
其它名稱： 82V3280PFG
IDT82V3280
WAN PLL
Thermal Management
150
December 9, 2008
8.4
TQFP EPAD THERMAL RELEASE PATH
In order to maximize both the removal of heat from the package and
the electrical performance, a land pattern must be incorporated on the
Printed Circuit Board (PCB) within the footprint of the package corre-
sponding to the exposed metal pad or exposed heat slug on the pack-
age, as shown in Figure 27. The solderable area on the PCB, as defined
by the solder mask, should be at least the same size/shape as the
exposed pad/slug area on the package to maximize the thermal/electri-
cal performance. Sufficient clearance should be designed on the PCB
between the outer edges of the land pattern and the inner edges of pad
pattern for the leads to avoid any shorts.
Figure 27. Assembly for Expose Pad thermal Release Path (Side View)
While the land pattern on the PCB provides a means of heat transfer
and electrical grounding from the package to the board through a solder
joint, thermal vias are necessary to effectively conduct from the surface
of the PCB to the ground plane(s). The land pattern must be connected
to ground through these vias. The vias act as ‘heat pipes’. The number
of vias (i.e. ‘heat pipes’) are application specific and dependent upon the
package power dissipation as well as electrical conductivity require-
ments. Thus, thermal and electrical analysis and/or testing are recom-
mended to determine the minimum number needed. Maximum thermal
and electrical performance is achieved when an array of vias is incorpo-
rated in the land pattern. It is recommended to use as many vias con-
nected to ground as possible. It is also recommended that the via
diameter should be 12 to 13mils (0.30 to 0.33mm) with 1 oz copper via
barrel plating. This is desirable to avoid any solder wicking inside the via
during the soldering process which may result in voids in solder between
the exposed pad/slug and the thermal land. Precautions should be taken
to eliminate any solder voids between the exposed heat slug and the
land pattern. Note: These recommendations are to be used as a guide-
line only. For further information, please refer to the Application Note on
the Surface Mount Assembly of Amkor’s Thermally/Electrically Enhance
Leadfame Base Package, Amkor Technology.
PIN
THERMAL
VIA
SOLDER
GROUND
PLANE
LAND
PATTERN
(GROUND PAD)
PIN
PAD
SOLDER
EXPOSED HEAT SLUG
PIN
PAD
SOLDER
相關PDF資料
PDF描述
MS27467E25B19SC CONN PLUG 19POS STRAIGHT W/SCKT
IDT82V3280DQG IC PLL WAN SE STRATUM 2 100-TQFP
MS27467E25B19SB CONN PLUG 19POS STRAIGHT W/SCKT
IDT82V3280PFG8 IC PLL WAN SE STRATUM 2 100-TQFP
MS3127E20-41P CONN RCPT 41POS BOX MNT W/PINS
相關代理商/技術參數
參數描述
IDT82V3280PFG8 功能描述:IC PLL WAN SE STRATUM 2 100-TQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT
IDT82V3280PFGBLANK 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:WAN PLL
IDT82V3285 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:WAN PLL
IDT82V3285AEQG 功能描述:IC PLL WAN SE STRATUM 100TQFP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT
IDT82V3285AEQG8 制造商:Integrated Device Technology Inc 功能描述:IC PLL WAN SE STRATUM 100TQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*