- 您現在的位置：買賣IC網 > PDF目錄360864 > INA156 Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier PDF資料下載
參數資料
| 型號： | INA156 |
| 元件分類： | 測量放大器 |
| 英文描述： | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| 中文描述： | 單電源，軌至軌，低成本儀表放大器 |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 114K |
| 代理商： | INA156 |
8
INA156
APPLICATIONS INFORMATION
Figure 1 shows the basic connections required for operation
of the INA156. Applications with noisy or high impedance
power supplies may require decoupling capacitors close to
the device pins, as shown.
The output is referred to the output reference terminal, Ref,
which is normally set to V
S
/2. This must be a low-imped-
ance connection to ensure good common-mode rejection.
In addition, for the G = 50 configuration, the connection
between pins 1 and 8 must be low-impedance. A connection
impedance of 20
can cause a 0.2% shift in gain error.
OPERATING VOLTAGE
The INA156 is fully specified and guaranteed over the supply
range +2.7V to +5.5V, with key parameters guaranteed over
the temperature range of –55
°
C to +125
°
C. Parameters that
vary significantly with operating voltages, load conditions or
temperature are shown in the Typical Performance Curves.
The INA156 can be operated from either single or dual
power supplies. By adjusting the voltage applied to the
reference terminal, the input common-mode voltage range
and the output range can be adjusted within the bounds
shown in the Typical Performance Curves. Figure 2 shows
a bridge amplifier circuit operated from a single +5V power
supply. The bridge provides a relatively small differential
voltage on top of an input common-mode voltage near 2.5V.
FIGURE 1. Basic Connections.
FIGURE 2. Single-Supply Bridge Amplifier.
Ref
22.2k
200k
5k
Gain Pins Open:
G = 10
External Resistor R
G
:
10 < G < 50
Gain Pins Connected:
G = 50
5k
200k
22.2k
4
3
2
5
7
1
8
V–
0.1
μ
F
Dual Supply
Single Supply
Also drawn in simplified form:
V+
INA156
INA156
6
1
3
8
2
V
OUT
6
7
4
5
Ref
0.1
μ
F
V+
V–
DESIRED GAIN
(V/V)
R
G
(
)
10
20
30
40
50
Open
30k
10k
3.3k
Short
G = 10 +
400k
10k
+ R
G
V
IN
–
V
IN
+
A1
A2
V
IN
+
V
IN
–
V
OUT
= (V
IN
– V
IN
) G + V
REF
+
–
Bridge
Sensor
INA156
V
REF(1)
+5V
3
2
4
5
7
6
V
OUT
= 0.01V to 4.99V
(2)
NOTES: (1) V
should be adjusted for the desired output level,
keeping in mind that the value of V
affects the common-mode
input range. See Typical Performance Curves. (2) For best
performance, the common-mode input voltage should be kept away
from the transition range of (V+) – 1.8V to (V+) – 0.8V.
1
8
V
IN
+
V
IN
–
相關PDF資料 |
PDF描述 |
|---|---|
| INA156A | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA156E | Single Supply, Rail-to-Rail, Low Cost Instrumentation Amplifier |
| INA157UA | High-Speed, Precision DIFFERENCE AMPLIFIER |
| INA157 | High-Speed, Precision DIFFERENCE AMPLIFIER |
| INA157U | High-Speed, Precision DIFFERENCE AMPLIFIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| INA156A | 制造商:BB 制造商全稱:BB 功能描述:Single-Supply, Rail-to-Rail Output, CMOS INSTRUMENTATION AMPLIFIER |
| INA156E | 制造商:BB 制造商全稱:BB 功能描述:Single-Supply, Rail-to-Rail Output, CMOS INSTRUMENTATION AMPLIFIER |
| INA156EA/250 | 功能描述:儀表放大器 Single-Sply R-to-R Output CMOS RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA156EA/250G4 | 功能描述:儀表放大器 Single-Sply R-to-R Output CMOS RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
| INA156EA/2K5 | 功能描述:儀表放大器 Single-Sply R-to-R Output CMOS RoHS:否 制造商:Texas Instruments 通道數量: 輸入補償電壓:150 V 可用增益調整: 最大輸入電阻:10 kOhms 共模抑制比（最小值）:88 dB 工作電源電壓:2.7 V to 36 V 電源電流:200 uA 最大工作溫度:+ 125 C 最小工作溫度:- 40 C 封裝 / 箱體:MSOP-8 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。