參數資料
型號： IP113M
英文描述： Managed 10/100Base-TX / FX Media Converter
中文描述： 托管個10/100Base-TX /外匯收發器
文件頁數： 14/27頁
文件大?。?/td> 186K
代理商： IP113M
IP113
Preliminary, Specification subject to change without notice
IP113-DS-P07
Jul. 19, 2002
14
Link Fault Pass Through
IP113 supports link fault pass through in TX/FX converter
application. This function is enabled if pin 57(LFP) is tied
to VCC. When IP113 works at this mode, port 0 is a TP
port with auto-negotiation capability and port 1 is a fiber
port. Link status on one port is propagated to the other
port to notice the remote nodes.
If TP port is unplugged, IP113 stops transmission on fiber
port. This causes the remote fiber node link fails. LED
shows link failure on both TP port and fiber port. If fiber
link fails, IP113 restarts auto-negotiation on TP port but
always stays in the link failure state. This causes the
remote TP node link fails. LED shows link failure on both
TP port and fiber port.
LED and Initial Value Setting
IP113 supports two ways to modify its initial values of
operation parameters to fit different applications. It read
the initial value via pins or EPROM interface.
Initial Value Set Via Pins
To set the parameter via pins, connect them to vcc or
ground through resistors. IP113 reads initial value via
pins during the period of reset. An initial value is set to
1’b1 (1’b0) by connecting a pin to vcc (gnd) through a
10k
(1k
) resistor as shown on the following figure.
The function begins after the internal PLL clock active. To
make sure the proper operation of PLL, the duration of
reset must be no less than 1 ms. When there is no
setting resistor, IP113 uses the default value.
IP113 reads initial setting via pins during the period of
reset. At reset, these pins are input signals and IP113
reads the initial value. After reset, LED pins become
output signals and show LED functions at normal mode.
The application circuit is shown below.
2.5V
To set initial value = 1
with pull up 10K ohm resister
To set initial value = 0
with pull down 1K ohm resister
LED PIN
10K
220
LED PIN
1K
2.5V
220
To use default value
(use no resistor to leave it open)
LED PIN
2.5V
220
相關PDF資料
PDF描述
IP117AK-BSS2 Voltage Regulator
IP117AK-DESC Voltage Regulator
IP117AR Voltage Regulator
IP117AR-883B Voltage Regulator
IP117AR-BSS2 Voltage Regulator
相關代理商/技術參數
參數描述
IP113MLF 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Managed 10/100Base-TX / FX Media Converter
IP113MLF-DS-R01 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Managed 10/100Base-TX / FX Media Converter
IP113MLF-DS-R02 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Managed 10/100Base-TX / FX Media Converter
IP113MLF-DS-R03 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Managed 10/100Base-TX / FX Media Converter
IP113MLF-DS-R04 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Managed 10/100Base-TX / FX Media Converter
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*