- 您現在的位置：買賣IC網 > PDF目錄360912 > IQ80C154-L16 CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller PDF資料下載
參數資料
| 型號： | IQ80C154-L16 |
| 英文描述： | CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| 中文描述： | 的CMOS 0至36 MHz的單芯片8位微控制器 |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 354K |
| 代理商： | IQ80C154-L16 |
Rev.F (14 Jan. 97)
7
MATRA MHS
Power Down
External
0
0
Floating
Port Data
Port Data
Port Data
Figure 4. I/O Buffers in the 83C154 (Ports 1, 2, 3).
Stop Clock Mode
Due to static design, the TEMIC 83C154 clock speed can
be reduced until 0 MHz without any data loss in memory
or registers. This mode allows step by step utilization, and
permits to reduce system power consumption by bringing
the clock frequency down to any value. At 0 MHz, the
power consumption is the same as in the Power Down
Mode.
I/O Ports
The I/O drives for P1, P2, P3 of the 83C154 are
impedance programmable. The I/O buffers for Ports 1, 2
and 3 are implemented as shown in
figure 4
.
When the port latch contains 0, all pFETS in figure 4 are
off while the nFET is turned on. When the port latch
makes a 0-to-1 transition, the nFET turns off. The strong
pullup pFET, T1, turns on for two oscillator periods,
pulling the output high very rapidly. As the output line is
drawn high, pFET T3 turns on through the inverter to
supply the IOH source current. This inverter and T3 form
a latch which holds the 1 and is supported by T2. When
Port 2 is used as an address port, for access to external
program of data memory, any address bit that contains a
1 will have his strong pullup turned on for the entire
duration of the external memory access.
When an I/O pin on Ports 1, 2, or 3 is used as an input, the
user should be aware that the external circuit must sink
current during the logical 1-to-0 transition. The
maximum sink current is specified as ITL under the D.C.
Specifications.
When
the
approximately 2 V, T3 turns off to save ICC current. Note,
when returning to a logical 1, T2 is the only internal
pullup that is on. This will result in a slow rise time if the
user’s circuit does not force the input line high.
The input impedance of Port 1, 2, 2 are programmable
through the register IOCON. The ALF bit (IOCON0) set
all of the Port 1, 2, 3 floating when a Power Down mode
occurs. The P1HZ, P2HZ, P3HZ bits (IOCON1,
IOCON2, IOCON3) set respectively the Ports P1, P2, P3
in floating state. The IZC (IOCON4) allows to choose
input impedance of all ports (P1, P2, P3). When IZC = 0,
T2 and T3 pullup of I/O ports are active ; the internal input
impedance is approximately 10 K. When IZC = 1 only T2
pull-up is active. The T3 pull-up is turned off by IZC. The
internal impedance is approximately 100 K.
input
goes
below
Oscillator Characteristics
XTAL1 and XTAL2 are the input and output respectively,
of an inverting amplifier which is configured for use as an
on-chip oscillator, as shown in figure 5. Either a quartz
crystal or ceramic resonator may be used.
Figure 5. Crystal Oscillator.
To drive the device from an external clock source,
XTAL1 should be driven while XTAL2 is left
unconnected as shown in
figure 6
. There are no
requirements on the duty cycle of the external clock
signal, since the input to the internal clocking circuitry is
through a divide-by-two flip-flop, but minimum and
maximum high and low times specified on the Data Sheet
must be observed.
相關PDF資料 |
PDF描述 |
|---|---|
| IQ83C151C-12 | CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| IQ83C151C-16 | CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| IQ83C151C-20 | CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| IQ83C151C-25 | CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
| IQ83C151C-30 | CMOS 0 to 36 MHz Single Chip 8-bit Microcontroller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IQ80T B | 制造商:Omnimount 功能描述:Tilt Mount for Flat Panel Televisions 23"~42" 80lb. Capacity 制造商:OMNIMOUNT 功能描述:DWO FLAT PANEL MOUNT TILT FOR 23 IN - 42 IN FLAT PANELS |
| IQ81349SC 888389 | 制造商:Intel 功能描述:IQ81349SC - Bulk |
| IQ82C55A | 功能描述:IC I/O EXPANDER 24B 44MQFP RoHS:否 類別:集成電路 (IC) >> 接口 - I/O 擴展器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 接口:I²C，JTAG 輸入/輸出數:9 中斷輸出:無 頻率 - 時鐘:400kHz 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 包括:EEPROM |
| IQ82C55A96 | 功能描述:IC I/O EXPANDER 24B 44MQFP RoHS:否 類別:集成電路 (IC) >> 接口 - I/O 擴展器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 接口:I²C，JTAG 輸入/輸出數:9 中斷輸出:無 頻率 - 時鐘:400kHz 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 包括:EEPROM |
| IQ82C55AZ | 功能描述:外圍驅動器與原件 - PCI PERI PRG-I/O 5V 8MHZ INDUSTRIAL TEMP RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。